background image

frequency energy, and if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment 
does cause interference to radio or television equipment reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures:

 

Reorient or relocate the receiving antenna.

 

Move the equipment away from the receiver.

 

Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

Consult the dealer or an experienced radio/television technician for additional suggestions.

CAUTION! Any changes or modifications to this equipment not expressly approved by the party 
responsible for compliance could void your authority to operate the equipment.

RF Exposure Information

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.9”) 
from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. 

IC Compliance Information

Radio Equipment Notice

The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications 
were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and 
(2) this device must accept any interference, including interference that may cause undesired operation of the 
device. “Privacy of communications may not be ensured when using this device”.

CE Compliance Information

Products with CE Marking comply with EMC Directive (2004/108/EC); Low Voltage Directive (73/23/EEC); 
R&TTE(1999/5/EC) issued by the Commission of the European Community. Compliance with these directives 
implies conformity to the following European Norms:

 

EMC: EN 301 489

 

LVD: EN 60950

 

Radio: EN 300 328

One-year Limited Warranty

Important: Evidence of original purchase is required for warranty service.

Summary of Contents for UDW10055



























Reviews: