background image

 

 

3

 

Technical Specifications 

3.1

 

Electrical Specifications 

Absolute Maximum Ratings 

Item  

Pin  

Min  

Max  

Unit 

Condition  

Power Supply (VCC)  

Vcc  

-0.5 

3.6 

 

VCC Ripple 

Vrpp 

 

50 

mV 

 

Digital IO  

Vin  

-0.5 

Vcc +0.2 

 

Storage Temperature  

Tstg  

-45 

90 

 

 

MSD (MSL) 

Level 1   

Level 2   

Level 3   

TBD 

3.2

 

Operation Condition 

Item 

Pin 

Min 

Typical 
Value 

Max 

Unit 

Condition 

Power Supply (VCC)  

Vcc  

2.8 

3.3 

3.6 

  

Peak current 

Iccp  

 

 

37 

mA 

Vcc=3.0 V  

Tracking average 
current 

I

ACQ

 

19 

20 

21 

mA 

Vcc=3.0V 

Low level input voltage 

Vin_low 

 

 

0.7 

 

High level input voltage 

Vin_high 

1.2 

 

 

 

Low level output voltage  Vout_low    

 

0.4 

Iout=-8 mA  

High level output 
voltage 

Vout_high   Vcc–0.4   

 

Iout=8 mA  

Antenna gain 

Gant  

15 

 

30 

dB 

 

Nosie figure 

Nftot  

 

 

dB 

 

Operation Temperature 

Topr  

-40 

 

85 

 

 

3.3

 

Dimensions 

Table 3-1: Dimensions 

Symbol 

Min(mm) 

Typical Value(mm) 

Max(mm) 

9.6 

10.1 

10.7 

9.55 

9.7 

9.85 

2.1 

2.2 

2.3 

0.55 

0.65 

0.95 

1.0 

1.1 

1.2 

F 

0.7 

0.8 

0.9 

G 

0.3 

0.4 

0.5 

Summary of Contents for UM220-IV M0




















Reviews: