UNI-T UT8803 User Manual Download Page 2

Page: 2 / 30

I. Introduction

UT8803 is a professional 6000 count benchtop multimeter with high accuracy and outstanding performance.
It supports multiple measurements:

AC/DC voltage
AC/DC current
Resistance
Frequency
Capacitance
Inductance
Audion (hFE)
Diode(LED)
Thyristor(SCR)
Continuity

Please carefully read and comply with all warnings and cautions in this manual.

II. Open box inspection

Open the package box and take out the instrument. Please check whether the following items are deficient
or damaged and contact your supplier immediately if they are.

User Manual(DVD-R)----------------------1pc

Test leads-------------------------------------1pair

Alligator clip test line-----------------------1pair

Power line------------------------------------1pc

Software DVD-------------------------------1pc

USB cable------------------------------------1pcs

Warranty--------------------------------------1pc

Warning

When the measured voltage is greater than 600V, The instrument cannot be used for

measurements in CAT II, CAT III and CAT IV environment

Summary of Contents for UT8803































Search results

Summary of Contents for UT8803

Reviews:

Related manuals for UT8803

Brands by name

Popular brands

UNI-T UT8803, User Manual

Search results

Summary of Contents for UT8803

Reviews:

Related manuals for UT8803

Brands by name

Popular brands