UNI-T UPO2000CS Series User Manual Download Page 62 | Manualshive

Page: 62 / 94

background image

UPO2000CS series User Manua

61

Chapter 7 Set Display System

You can set the display type of the waveform, display format, duration, grid brightness, and waveform
brightness. Press the DISPLAY key to enter the display menu.

Functions Options

Descriptions

Type

Vector

Using lines to display between samples

Point

Displays points directly

Format

YT

Display level on time scale

XY 1&2

Display Lissajous graph of CH1~CH2 waveforms

XY 3&4

Display Lissajous graph of CH3~CH4 waveforms (UPO2XX4CS
only)

Duration
Time

Close

Displayed waveform refreshes at normal rate

100ms/200ms/
500ms/1s/2s/
5s/10s

Displayed waveform refreshes after specified time

Continuous

Waveform refreshes at a continuous rate

Grid
Brightness

1%~100%

Set the grid brightness, Use Multipurpose knob to adjust settings

Waveform
Brightness

1%~100%

Set the waveform brightness, Use Multipurpose knob to adjust
settings

7.1 XY Pattern

The XY mode display is also called Lissajous graph.

•

When XY 1&2 are selected, the CH1 signal will be entered on the horizontal axis (X), and the CH2 on the

vertical axis (Y).

•

When XY 3&4 are selected, the CH3 signal will be entered on the horizontal axis (X), and the CH4 on the

vertical axis (Y). Only UPO2XX4CS have this feature.

•

In X-Y mode, when CH1 or CH3 are activated, use the horizontal POSITION knob to adjust the graph

horizontally. When CH2 or CH4 are activated, use the horizontal POSITION knob to adjust the graph
vertically.

The vertical SCALE knob to be used to adjust each channel’s amplitude level. The horizontal SCALE knob can be
used to adjust the time position in order to obtain a well displayed Lissajous graph.

«
...
60
61
62
63
64
...
»

Summary of Contents for UPO2000CS Series































































































Reviews:

No comments

Related manuals for UPO2000CS Series

Brand: 3M Pages: 2

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: Baroness Pages: 40

Brand: Baroness Pages: 40

Brand: BARKO LOADERS Pages: 85

Brand: Jackco Pages: 6

Brand: IDEAL Pages: 12

Brand: Fast Pages: 60

INTRAmatic 31 ES

Brand: KaVo Pages: 52

Quadra Force/Sys

Brand: American DJ Pages: 1

Brand: Sunrise Medical Pages: 9

Brand: Tektronix Pages: 54

Brand: obsta Pages: 37

Brand: Ace Pages: 37

Brand: Next Sight Pages: 55

Tracer pH/TDS/Salt/Temp PockeTester

Brand: LaMotte Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands