background image

RIGHT FLOW

LEFT FLOW

RO FILLING

Unger Control Unit Introduction

v11 Unger

Leading Control Technology

with simple plug and go

connections...

Unger Control Unit Introduction

The Unger Control Unit provides leading control technology with simple

ease of use. Use the unit to make high quality pure water for excellent

cleaning results time after time with the 'RO FILLING' control.

Use the 'LEFT FLOW' and 'RIGHT FLOW' to give simple but accurate

flow control from two powerful delivery pumps.

Control your pumps remotely using the radio fobs and set to 'wash' for

cleaning or switch to 'rinse' for a boost. Press on/off to efficiently control

your water use.

Contents

P1 Unger Control Unit Introd Contents

P2 Unit Overview

P3 Connection Overview

P4 LEFT+RIGHT FLOW Quick Start Part 1

P5 LEFT+RIGHT FLOW Quick Start Part 2

P6 LEFT+RIGHT FLOW Three Button Radio Remote

P7 RO Quick Start Part 1

P8 RO Quick Start Part 2

P9 RO Autofill - Tank Filling

P10 RO TDS

P11 RO Power-Up Menu Settings

P12 General Settings - LEFT+RIGHT FLOW and RO

Keyfob

...easy to use operation

and labour saving features

Summary of Contents for nLite HydroPower XXL














Reviews: