PN 400847
UK4AA eLED CPO-ET
Instructions
BR
Bezel
14875
LED module
O-ring
Switch
Case
Vent
cell
4
cell
3
cell
2
cell
1
UK4AA eLED CPO
Congratulations on the purchase of
your Underwater Kinetics all
environment work torch! The UK 4AA
eLED CPO light is loaded with
features to help you work more
safely and efficiently normal and
wet environments.
Quality Features
• High-intensity 3-watt white LED lasts
thousands of hours without burning out
• Constant brightness over 70% battery
life
• Patented optical system reduces glare
by concentrating light into the main beam
with minimum side light
• Thermal Recovery System transfers
heat from LED to warm batteries for better
cold weather performance
• Waterproof pushbutton switch
• Attaches to helmet with accessory clip
• Passes 2 m drop test
• Watertight and dustproof with IP 68
up to 3 m water depth
• Corrosion and impact resistant graphite
filled case
• Ex-tested and certified in accordance
with the latest Directive 94/9/EC Guidelines,
for use in zone 1 potentially explosive
atmospheres
Accessories
• Holders are available for attaching
the UK 4AA eLED CPO torch to fire
brigade and safety helmets.
• Signal wand extension for directing
traffic
• Nylon pouch for attaching the UK
4AA eLED CPO to a belt.
Technical Data UK4AA eLED CPO
brightness: 120 lumens
burn time: 5 hours
batteries: 4AA alkaline
/LR6/mignon cells
DURACELL PROCEL
MN1500, DURACELL
PLUS MN1500, or
ENERGIZER
lNDUSTRIAL
EN91/AM3)
lamp type: High-Intensity LED
test depth: 3 m
beam travel: 192 m
size: 162 x 41 x 36 mm
weight: 177 g (incl. batteries)
materials: Graphite PC/ABS,
Polycarbonate,
TPU Rubber, Copper
CERTIFICATION INFORMATION
UK4AA eLED CPO-ET
1. Read the instructions before use.
2. Do not open torch in zone 1 or zone 2
hazardous locations.
3. Use only Part No. 14875
replacement lamp module.
4. Use only
DURACELL PROCEL
MN1500, DURACELL PLUS
MN1500, or ENERGIZER
lNDUSTRIAL EN91/AM3
AA/LR6/mignon alkaline batteries
5. Manufactured by
Underwater Kinetics
13400 Danielson Street
Poway, CA 92064
USA
(858) 513-9100 tel
(858) 513-9111 fax
6. A copy of the ATEX testing
certificate is available from
Underwater Kinetics directly
or their website
www.uwkinetics.eu
WARRANTY
Underwater Kinetics warrants that
this product is free from defects in
materials and manufacturing for a
period of 10 years from the date of
purchase under normal use. In
addition, the Underwater Kinetics
Limited Warranty covers materials
used in its products to the original
purchaser, from the date of purchase,
as follows: plastics for 10 years; rubber
for 3 years, LED and electronics for
1 year, rechargeable batteries for
90 days (batteries and lamps are not
manufactured by Underwater
Kinetics). This warranty is limited to the
first purchaser of the product and is
not transferable. This product is not
warranted if it is modified or used
inappropriately.
If the original retail purchaser
detects a defect in the material or
workmanship, the product along with
proof of purchase date should be
returned (postage prepaid) to an
authorized Underwater Kinetics dealer
in the area or directly to UKE
Underwater Kinetics Europe.
Underwater Kinetics agrees to repair
or replace at Underwater Kinetics' sole
discretion any product found to be
defective in material or workmanship
within the time period specified above.
This warranty is not valid when
handled by third parties which are not
authorized by Underwater Kinetics or
its distributors. Nothing contained
within these warranty terms detracts
from your Statutory Rights.
Address all correspondence and
returns to:
UKE Underwater Kinetics Europe GmbH
Beethovenstr. 279
D-42655 Solingen
Germany
tel: +49 212 242 13-0
fax: +49 212 242 13-30
email: [email protected]
web: www.uwkinetics.eu
Zone 1
SEV 08 ATEX 0164
II 2G Ex e ib IIC T4
II 2D Ex ibD 21 T98 °C
CAUTION
Batteries can vent hydrogen gas
and possibly cause an explosion
(1) if they are installed without the
proper polarity, (2) if they are not the
same type, brand name and age or
(3) if they are completely discharged.
• Load batteries according to
the diagram.
• Discard all batteries as soon as
they are drained or no longer
produce light.
• Do not mix batteries of different
type, brand or age.
ON/OFF
To operate the UK 4AA eLED CPO
push in on the black rubber switch to
turn the torch on and off. Make sure
the bezel is screwed all of the way
down or the UK 4AA eLED CPO will
not light. By partially unscrewing the
bezel you can protect the torch from
turning on by accident.
O-Ring Seal
The O-ring and threads must always
be kept clean. Lightly lubricate the
O-ring which seals the rubber
covered bezel and case with silicone
grease. Remove the O-ring by hand.
Do not use tools.
WARNING
In order to maintain the ATEX safety
rating, use only model 14875 lamp
module.
Pressure Equalizing Vent
Air and gas from battery leakage
can pass freely in and out of the UK
4AA eLED CPO through a vent in the
rear of the torch. Do not allow dirt or
grease to accumulate on the vent or
it will not operate properly.
Care and Maintenance
• Keep area around the 0-ring clean.
• If the torch floods, empty it
immediately, rinse with fresh water
and dry completely before reassembly.
• Replace the reflector/lamp, which
contains a hydrogen absorbing
catalyst , if it gets wet.
• Do not store batteries in the torch
for long periods of time when not
in use; they may leak and damage
the torch.
Battery Installation
To install batteries, hold the case in
the position shown. Drop the
batteries one by one into the case in
the order shown. Make sure that the
(+) end of batteries 1 and 2 is down
and up for batteries 3 and 4. Next
insert the lamp module into the case.
Place the bezel over the lamp module
and screw it onto the case.
Note: The torch will not light if the
batteries are inserted improperly.
OPERATING INSTRUCTIONS AND IMPORTANT INFORMATION
