WARNING!
This product is part of a personal fall
arrest system. The user must read
and follow the manufacturer’s
instructions for each component of
the system. These instructions must
be provided to the user of this
product. The user must read and
understand
these
instructions
before
using
this
product.
Manufacturer’s instructions must be
followed for proper use and
maintenance of this product.
Alteration or misuse of this product,
or failure to follow instructions may
result in serious injury or death.
1
USER INSTRUCTION MANUAL
MODEL:
96426SR, 96424S, 96426S, 96426SYSR, 96513, 96516, 96516PH, 96516Y,
96516YCTPH 96516YPH, 96516YSR, 96516YSRADJ, US-96516, US-96516Y,
US-96516YSR, US-96516L, US-96516LYSR, US-96516LYCA, 96516LBB, 96516BB,
96516YBB, 96516LSD, 96516SD, 96516YSD, 96516HD, 96516YSRH, 96516YACAHD
DESCRIPTION:
LANYARD WITH SHOCK PACKS, 3600 LB GATES
MEETS OSHA & ANSI Z359.1 | APPROVED FOR SHARP LEADING EDGE
1-800-850-5914
PHOENIX, AZ USA
WWW.ULTRASAFEUSA.COM
MODEL:_______________
SIZE: _________________
DATE: _________________
Anchorage:
The anchorage to which this product is
attached must be capable of sustaining a static load in the
direction applied by the personal fall arrest system of at least
3600 lbs. with certification of a qualified person or 5000 lbs.
without certification. When more than one personal fall
arrest system is attached to the same structure, the strength
requirements stated above must be multiplied by the number
of personal arrest systems attached to the structure.
Plan your personal fall protection system.
Before installing
and using this equipment, consider all factors affecting your
safety during use of this equipment.
Warning:
Manufacturer's instructions supplied
with this product at time of shipment must be followed.
Failure to do so could result in serious injury or death.
Contact manufacturer if instructions are needed.
• Warnings and instructions must be read
and understood before using equipment.
• Equipment must be used by trained
personnel only.
• Users must understand all OSHA regulations, ANSI
standards, and other relevant regulations and
standards pertaining to fall protection equipment.
This product is part of a personal fall
arrest system; a fall arrest system is
required if there is any risk that a
worker may fall from an elevated
position. It is a requirement that the
fall arrest system be used any time a
working height of six feet or more is
reached. Working height is defined as
the distance from the walking /
working surface to a
grade or lower level.
THE FOLLOWING IS RECOMMENDED
AS PART OF FALL ARREST SYSTEM
A. Shock Absorbing Lanyard
Material: Nylon
Warning tags located
in front and back of shock
absorber or located towards
hook, D-ring or eye end.
• Energy absorber resting force 900 lbs.
Plus 42 inch maximum extension.
• Rig lanyard to allow a maximum free fall distance
of not more than six feet.
• Connectors and anchorage points must be
compatible and able to support 5,000 lbs.
• Do not allow lanyard to contact sharp or abrasive
surfaces, sparks or temperature above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1") must not be connected to D-rings
on harnesses and belts.
• Remove from service if any damage is detected.
B. Anchorage connector
material: Nylon
Warning tags are
located towards hook,
D-ring or eye end.
• Use energy absorbers or retractable lanyards
when hazard of free fall can occur.
• Connectors and anchorage points must be compatible
and able to support 5,000 lbs. Always work directly
under anchorage to avoid a swing fall injury.
• Anchorage and tie off points must be at a height
that will not allow a lower level to be struck should
a fall occur. Do not allow product to contact sharp
or abrasive surfaces, sparks or temperatures
above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1”) must not be connected.
• Remove from service if any damage is detected.
Same, but 100% Tie-Off.
313L1
1.
2.
3.
4.
5.
6.
7.
1. Back 'D' ring is for fall arrest
2. Shoulder 'D' rings. (if present) are for retrieval use
only use locking snaps.
3. Side 'D' rings (if present) are for positioning only.
4. Front 'D' ring (if present) is for fall arrest
(foot first falls only, 2 foot max free fall), work
positioning, travel restraint or rescue
5. Hip attachment elements are for work positioning
or travel restraint
6. Visual load indicator
7. Park lanyard here
NOTE:
See additional instructions on buckle adjustment
for proper fit. Maximum free-fall distance six feet or
energy absorber arresting force of 900 lbs per ANSI or
maximum fall arrest force of 1800 lbs per OSHA.
Avoid lower level contact.
