manualshive.com logo in svg

ULS VLS Series, Service Manual

Share
Download
ULS VLS Series Service Manual Download Page 32

VLS Service Manual - REV2015.04

Table of Contents

Component Removal and Replacement

Page | 32

Component Removal and Replacement

VLS6.60

NOTE:

 

The assistance of one or two people is recommended.

1.  Power OFF and unplug the VLS.

2.  Open the rear cover by pressing down on the button part of the latches until the latches pop up.

3.  Fold the Rear Cover to its resting position.

4.  Remove the latch retaining bracket by removing the screw holding it in place. The latch will be 

removable.

5.  Installation is opposite of removal. Continue to step 6 if replacing the Rear Cover Latch Catches.

6.  Fold the cover down to a resting position.

7.  Remove the two screws and two washers holding each of the cover latches in position.

8.  Installation is opposite of removal.

Rear Cover Latches and Cover Latch Catch

VLS3.60 and VLS4.60

NOTE:

 The assistance of one or two people is recommended.

1.  Power OFF and unplug the VLS.

2.  Open the rear cover by pulling the latches toward the back of the system.

3.  Fold the Rear Cover to its resting position.

4.  Depress the small plastic flange holding the latch.

5.  While depressing the flange push the latch out of the cover.

6.  Installation is opposite of removal. Continue to step 7 if replacing the Rear Cover Latch Catches.

7.  Fold the cover down to a resting position.

8.  Remove the two screws and two washers holding each of the cover latches in position.

9.  Installation is opposite of removal.

Summary of Contents for VLS Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands