manualshive.com logo in svg

ULS VLS Series, Service Manual

Share
Download
ULS VLS Series Service Manual Download Page 30

VLS Service Manual - REV2015.04

Table of Contents

Component Removal and Replacement

Page | 30

Component Removal and Replacement

Rear Cover Filter Media and Fan Guard

1.  Power OFF and unplug the VLS.

2.  Firmly grip the top two corners of the fan cover and pull away. The cover will pop off.

3.  Remove the fan media.

4.  Remove the screws holding the fan grilles in place.

5.  Installation is opposite of removal.

7.  Using a 9/64” Allen wrench, check to ensure the new Collimator has the correct gap. The width of the 

Allen wrench is approximately the correct gap.

8.  Perform a 

Laser Beam Check and Alignment

, however, instead of adjusting the #2 mirror adjust the 

Collimator using the three small setscrews by rotating them in extremely small increments, one at a time 
until the beam is aligned.

NOTE:

 Access the setscrews through the holes on the front of the collimator.

9.  Installation is complete.

Summary of Contents for VLS Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands