ULS VLS Series Service Manual Download

Page: 29 / 82

VLS Service Manual - REV2015.04

Table of Contents

Component Removal and Replacement

Page | 29

Component Removal and Replacement

Collimator

1. Make sure the VLS is powered OFF and unplugged.

2. Open the Top Door and pull the X-axis Arm completely forward.

3. Remove the two screws holding the Collimator in place.

4. Carefully remove the Collimator and place in a safe location.

5. With the Collimator uninstalled, perform a

Laser Beam Check and Alignment

6. Once the Laser Beam Check and Alignment is complete install the Collimator using the screws

removed earlier.

Beam Window

1. Make sure the VLS is powered OFF and unplugged.

2. Open the Top Door and pull the X-axis Arm completely forward.

3. Remove the two screws holding the Beam Window in place.

4. Carefully remove the Beam Window.

5. Installation is opposite of removal.

Summary of Contents for VLS Series



















































































Search results

Summary of Contents for VLS Series

Reviews:

Related manuals for VLS Series

Brands by name

Popular brands

ULS VLS Series, Service Manual

Search results

Summary of Contents for VLS Series

Reviews:

Related manuals for VLS Series

Brands by name

Popular brands