Udoo VISION User Manual Download

Page: 43 / 67

VISION

4.3

Advanced menu

Menu Item

Options

Description

Trusted Computing

See submenu

Trusted Computing Settings

ACPI Settings

See submenu

System ACPI parameters

S5 RTC Wake Settings

See submenu

Enable system to wake from S5 using RTC alarm

CPU Configuration

See submenu

CPU Configuration Parameters

AMI Graphic Output Protocol Policy

See submenu

User Selected Monitor Output by Graphic Output protocol

PCI Subsystems Settings

See submenu

PCI Subsystems Settings

Network Stack Configuration

See submenu

Network Stack Settings

CSM Configuration

See submenu

Compatibility Support Module(CSM)

NVMe Configuration

See submenu

NVMe Device Options Settings

SDIO Configuration

See submenu

SDIO Configuration Parameters

USB Configuration

See submenu

USB Configuration Parameters

Platform Trust technology

See submenu

Platform Trust Technology

Main Thermal Configuration

See submenu

Main Thermal Configuration

HSUART Transceiver Configuration

See submenu

HSUART Transceiver Configuration Utility

SMBIOS Information

See submenu

SMBIOS Information

Embedded Controller

See submenu

Embedded Controller Parameters

M.2 peripheral management

See submenu

M.2 peripheral management

Summary of Contents for VISION


































































Search results

Summary of Contents for VISION

Reviews:

Related manuals for VISION

Brands by name

Popular brands

Udoo VISION, User Manual

Search results

Summary of Contents for VISION

Reviews:

Related manuals for VISION

Brands by name

Popular brands