background image

Mr Bot 280 

35 

 

 

This  e-shop  also  reserves  its  right  to  interrupt  at  any  time  and  without  notice, 
partly or in whole, the provision of the website’s services. 

 

In any case, not exercising any of the rights stemming from the e-shop’s terms of 
use does not constitute a waiver of these rights. 

 

Product manufacturer’s and e-shop’s liability 

 

The manufacturer of the products available for purchase on this e-shop, as well 

as the e-shop itself, shall not be liable for the items produced by the purchased 

products  (e.g.  three-dimensional  objects  printed  with  or  without  the  use  of  the 

relevant  software  or  code)  or  the  purpose,  mode  and  potential  implications  of 

the  above  items’  use.  The  buyer/consumer  shall  be  solely  liable  for  the  items 

produced  by  the  purchased  products  and  for  their  proper  use  as  far  as  place, 

time,  cause  and  objective  are  concerned.  The  buyer/consumer  who  uses  the 

items  produced  by  the  purchased  products  undertakes  the  legal  obligation  to 

abide  by  the  safety  rules  and  to  fully  respect  their  fellow  citizens’  life,  health, 

bodily integrity, peace and quiet. With the exception of persons under the close 

supervision of a legally fully capable adult, the use of the purchased products by 

minors,  persons  placed  under  judicial  guardianship  and  persons  who  are,  in 

general and for any reason, incapable of protecting themselves or others from 

potential  dangers  arising  from  the  use  and  operation  of  the  products  available 

for  purchase  on  this  e-shop  and/or  the  items  produced  by  the  purchased 
products is explicitly forbidden. 

 

Governing law 

 

The  present  contract  shall  be  governed  by  and  construed  in  accordance  with 

Greek  Law  and  European  Law,  as  the  latter  has  been  incorporated  into  the 

former.  The  Courts  of  Athens  shall  have  exclusive  jurisdiction  to  settle  any 

dispute or claim between the user/consumer and the company arising out of or 
in connection with the website’s services or for any other reason. 

 

Summary of Contents for MR BOT 280









































Reviews: