UBI EasyCoder 91 Installation & Operation Manual Download Page 9 | Manualshive

Page: 9 / 50

UBI EasyCoder 91 Installation & Operation Manual Download Page 9

9

UBI EasyCoder 91 – Installation & Operation Ed. 1

Chapter 2 Windows Drivers

Windows Drivers

Installation
Disk

With the printer delivery comes a DOS-formatted 3.5"
HD floppy disk, that contain printer drivers for Easy-
Coder 71 and EasyCoder 91 (the latter with either 8
dots/mm or 12 dots/mm printhead density

1

). The drivers

are available for Microsoft Windows 3.1x and Windows
95 operating systems.

Using these printer drivers, you can print labels from
almost any Windows application and from the various
versions of UBI LabelShop label-design program.

The floppy disk also contains Winbar 2.5, a freeware
program from Stellar Technologies, that can generate
bar codes to the Windows Clipboard.

On the floppy disk, there are three directories:

• A:\win3xx\

contains Windows 3.1x printer driv-
ers for:
- EasyCoder 71 8 dots/mm
- EasyCoder 91 8 dots/mm
- EasyCoder 91 12 dots/mm

• A\:win95\

contains Windows 95 printer drivers
for:
- EasyCoder 71 8 dots/mm
- EasyCoder 91 8 dots/mm
- EasyCoder 91 12 dots/mm

• A:\wbar\

contains Winbar 2.5

Note that the Windows drivers do not work with
Windows 3.0 or earlier versions.

Install the UBI Windows Driver in Microsoft Windows
3.1x or Windows 95 according to the standard procedure
for printer driver installation (also see Microsoft Win-
dows manuals).

Note!
Windows for Workgroup Users:
If you during installation receive a warning stating
“The currently installed UNIDRV.DLL is newer...”,
click the “No” button (default).

Installation

Chapter 2

1

/. The exact printhead densities

are:
8 dots/mm = 203.2 dots/inch
11.81 dots/mm = 300 dots/inch

«
...
7
8
9
10
11
...
»

Summary of Contents for EasyCoder 91



















































Reviews:

No comments