manualshive.com logo in svg

UBI EasyCoder 91, Installation & Operation Manual, Page: 28 / 50

Share
Download
UBI EasyCoder 91 Installation & Operation Manual Download Page 28

28

UBI EasyCoder 91 – Installation & Operation Ed. 1

Chapter 3     Operation

Paper Load,

cont'd.

Tear-Off Operation – Labels

1

Open the printer's top cover by pressing the two cover
locks on either side and folding the cover upwards/
rearwards.

2

Pull the green carriage release lever, at the left side of
the print mechanism, forward and lift the print carriage
to open position.

3

Remove possible remaining paper or empty paper
core.

4

Place the spindle into the core of a fresh paper roll.

5

Place the paper roll and spindle in the open cover.

6

If loading paper for the first time after installation, or
if changing to a different paper width, use the green
wheel at the left side of the print mechanism to adjust
the paper guides so their positions correspond to the
width of the paper.

7

From the rear, insert the paper below the rounded rear
wall of the print mechanism and between the paper
guides until it protrudes in front of the tear-off edge.

8

Move the paper roll and spindle to the paper stock
compartment and let the spindle rest in the slots on
either side.

Summary of Contents for EasyCoder 91



















































Reviews:

No comments