manualshive.com logo in svg

UBI EasyCoder 91, Installation & Operation Manual, Page: 27 / 50

Share
Download
UBI EasyCoder 91 Installation & Operation Manual Download Page 27

27

UBI EasyCoder 91 – Installation & Operation Ed. 1

Chapter 3     Operation

Tear-Off Operation –  Tickets and Tags, cont'd.

9

Check that the paper guides allow the paper to run
smoothly without causing it to bulge, yet keep it
firmly centre-aligned. If necessary, use the green
wheel on the left side to fine-adjust.

10

If required, load a fresh supply of thermal transfer
ribbon according to the instructions in the chapter
“Ribbon Load”.

11

Close the print carriage by pressing it firmly down
simultaneously on both sides. A load click indicates
locked position.

12

Close the printer's top cover.

13

Tap the Feed key 4 times or until the indicator lamp
glows green.

14

If the printer did run out of paper while printing, the
printing will automatically be resumed. Else, tear off
excessive paper by pulling it down against the tear-off
edge.

HINT:
If you use the same paper width, you could reload the
paper supply by just opening the transparent cover and
insert the paper, while pressing the Feed key.

Paper Load,

cont'd.

Summary of Contents for EasyCoder 91



















































Reviews:

No comments