UBI EasyCoder 91 Installation & Operation Manual Download Page 2 | Manualshive

Page: 2 / 50

UBI EasyCoder 91 Installation & Operation Manual Download Page 2

2

UBI EasyCoder 91 – Installation & Operation Ed. 1

Preface

International Notices

FCC Notice (United States of America)

WARNING:

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been
tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15
of FCC Rules, which are designed to provide reasonable protection against such interference when oper-
ated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures may be
required to correct the interference.

DOC Notice (Canada)

Canadian Dept. of Communication

REGULATIONS COMPLIANCE (DOC-A)

This digital apparatus does not exceed the class A limits for radio noise emissions from a digital apparatus
as set out in the radio interference regulations of the Canadian Department of Communication.

❖ ❖ ❖ ❖ ❖ ❖

Ministère des Communications du Canada

CONFORMITE DE REGLEMENTS (DOC-A)

Le présent appareil numérique n´émet pas de bruits radio-électriques dépassant les limites applicables aux
appareils numériques de classe A prescrites dans le règlement sur brouillage radioélectrique édicté par le
Ministère des Communications du Canada.

VDE Notice (Germany)

ALLGEMEINE VORSCHRIFT:

Reparaturen oder sonstige Eingriffe, die sich nicht auf normale Bedienung der Maschine beziehen, dürfen
ausschließlich nur von einem ausgebildeten, zuständigen Fachmann vorgenommen werden.

Information in this manual is subject to change without prior notice and does not represent a commitment
on the part of UBI Printer AB.
© Copyright UBI Printer AB, 1996. All rights reserved. Published in Sweden.

EasyCoder is a trademark of United Barcode Industries.
Centronics is a registered trademark of Centronics Data Computer Corp.
IBM is a registered trademark of International Business Machines Corporation.
Microsoft is a registered trademark of Microsoft Corporation.
Windows is a trademark of Microsoft Corporation.

«
1
2
3
4
...
»

Summary of Contents for EasyCoder 91



















































Reviews:

No comments