uAvionix tailBeaconX TSO User And Installation Manual Download | Manualshive

Page: 12 / 46

background image

UAV-1004270-001

12

Rev A

5.5 FCC ID

Model

FCC ID

tailBeaconX TSO

2AFFTP200S

Contains

2AC7Z-ESPWROOM02U

5.6 Device Marking

5.6.1 tailBeaconX Hardware

5.6.2 tailBeaconX Universal Installation Kit

5.6.3 tailBeaconX ADS-B Software

The ADS-B software contained in the tailBeaconX is identified by electronic
marking. Reference Section 9.6 for information on determining the software
part number.

«
...
10
11
12
13
14
...
»

Summary of Contents for tailBeaconX TSO















































Reviews:

No comments

Related manuals for tailBeaconX TSO

SoundWorks Radio 820HD

Brand: Cambridge SoundWorks Pages: 12

Brand: Tecsun Pages: 36

Brand: Blaupunkt Pages: 28

Brand: AnyTone Pages: 13

Brand: Tokai Pages: 34

GHP Reactor Hydraulic

Brand: Garmin Pages: 14

CC Solar Observer

Brand: C. Crane Pages: 16

Brand: Odom Pages: 2

Brand: LENCO Pages: 3

Marine Master Clock 70000

Brand: Zenitel Pages: 118

Brand: Garmin Pages: 8

Brand: Vertex Standard Pages: 31

Brand: Vertex Standard Pages: 44

Brand: Fulljoin Pages: 37

TM80 - Clock Radio / Digital Audio Player

Brand: Timex Pages: 14

Brand: Timex Pages: 17

Brand: Fisher Pages: 11

Brand: DECODE Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands