background image

13

111299-06 - 9/22

SteamMax

Knock-Down Assembly Instructions

DANGER

• Use precautions and appropriate rigging 

apparatus when moving heavy objects.

• Use proper Personal Protective Equipment (PPE) 

during assembly.

5

 Split Section and Base Assembly

See Figures 5-1, 5-2, 5-3 and 3-2 for References.
1.  Either left section assembly or right section 

assembly can be secured first. Left section 

assembly will be secured first for purposes of this 

instruction.

 

NOTICE:  

 

Insulation between base and section 

assembly is not used. A high temperature silicone 

RTV will be used to seal base/section assembly 

joint after section assemblies are joined on base. 

See step 19.

2.  Screw (2) 5/16-18 hex head bolts, 

Item 1

, into 

holes in base.

3.  Lower left assembly, 

Item 2

, onto base with bolts 

centered in assembly slots.

4.  Tighten 5/16-18 nylon locking nuts and washers, 

Item 3

, onto bolts.

5.  Thoroughly clean nipples, 

Item 4

, and nipple 

ports with a de-greasing solvent.

6.  Evenly coat nipples and nipple ports with 

provided Loctite® 592.

7.  Place nipples in nipple ports and bump carefully 

with a wooden block to set.

8.  Apply provided SIL-BOND RTV 6500 to flue way 

joint. See Figure 5-1.

9.  Place right section assembly, 

Item 5

, onto base 

as close to left section assembly as possible 

aligning nipples to nipple ports.

10.  Screw together enough 3/4-10 x 11" draw rod 

using coupling nuts, 

Item 6

, to pass through 

section assemblies, 

Items 2 and 5

, draw plates, 

washers & nuts,

 Item 7

, on both sides. Two draw 

rods are required, one through upper nipple port 

and other through lower nipple port.

11.  Keep draw rod threads lubricated to reduce 

friction for easier assembly. 

12.  Draw section assemblies together slowly and 

evenly. Alternately tighten upper and lower draw 

rods. Tighten each draw rod a little at a time so 

sections are evenly spaced. Either base assembly 

and/or section assemblies may require adjusting 

to maintain nipple and nipple port alignments.

13.  Tighten until sections meet iron-to-iron. Small 

gaps, typically less than 1/16", between sections 

after assembly are normal.

 

NOTICE:  

 

Do not loosen or remove draw rods until 

tie rods are secured.

14.  Screw (2) 5/16-18 hex head bolts through base 

holes and section assembly slots on right side.

15.  Tighten 5/16-18 nylon locking nuts and washers 

onto bolts.

16.  Place 3/8-16 x 7-3/4" long tie rods, 

Item 8

, through 

top lug holes at upper and lower nipple ports.

17.  Tighten 3/8-16 nut and washer, 

Item 9

, onto each 

end of a tie rod until hand tight. This will allow for 

thermal expansion.

18.  Remove draw rods.
19.  Hydrostatically test section assembly.
 

NOTICE:  

 

 It is essential that hydrostatic testing 

be done before sealing block to base (step 

20) and before canopy, jacket, controls, and 

piping are installed. See Hydro-Test Section for 

procedure.

20.  Apply provided SIL-BOND RTV 6500 to entire 

perimeter of base/section assembly joint.  See 

Figure 5-2.

 

Flue Way

Joint

Flue Way

Joint

Figure 5-1:  Assembly Section Flue Way Joint

Apply Silicone

Here

Apply Silicone

Here

!

Summary of Contents for SteamMax STMX100









































Reviews: