Bedienungsanleitung / Exercise Monitor Instruction
6. Preset programs: This unit contains 25 preset programs
P1-P25. In standby mode, press the PROGRAM
button and the speed display will show P1-P12.
After selecting the desired program, the time display
flashes and displays the default value of 30:00 minutes.
Press “SPEED+”, “SPEED -” to set the desired workout
time. Press START, to start the selected program.
The default programs are in 10 intervals. Each interval
is one tenth of the time you set. During the workout you
can change the speed using the “SPEED+”, “SPEED -”
buttons, but it will jump again in the next interval Back to
the default value. The device beeps 3 times when the
program is finished and stops slowly. After 5 seconds
without activity, the unit goes into standby mode.
7. Body fat value measurement: Press the “PROGRAM”
button until you reach :FAT” body fat value measurement,
then press the “mode” button, the window will show
“F-1, F-2, F-3, F-4, F-5”. (F-1---Gender, F-2---Age,
F-3---Height, F-4---weight, F-5, Fat test) Press the
“SPEED - /+” buttons to change the values form
F-1 to F-4 (see the table below). The display then
shows F-5. keep both hands on the hand pulse for
2-3 seconds, and the display will show your BMI after
3 seconds. Body Fat is just a measurement between
height and weight not for body proportion. Body Fat
is suitable for male and female. See below table.
8. Trouble shooting.
Computer has no display. Check all cable connections
between computer and controller board, make sure
the connector pins are straight and not bent.
E01: Cable connection fail, check the cables
between the computer and controller board.
E02: Low Power voltage. Check if the controller board for
damage or burning smell, or check the motor
connection cable.
E03: No speed sensor detected, check the speed sensor is
in correct position, dirty or broken. Clean and re-assemble
if needed, if still not working, replace speed sensor.
E04: Incline issue. Check the incline motor cable
connections.
E05: Overcurrent or something causing the motor to not
work. Clean the running board, add the silicon oil onto
running board,as per pages 28-31. Then re-start the machine.
E08: The controller board is faulty, replace controller board.
If start the machine, but motor not working, then check
the motor connection cable, or check the controller board.
F-1
F-2
F-3
F-4
F-5
Körperfett-Wert / FAT
Körperfett-Wert / FAT
Körperfett-Wert / FAT
Körperfett-Wert / FAT
Untergewicht / Underweight
=(20---25)
Fettleibigkeit / Obesity
Geschlecht / Gender
Alter / Age
Größe / Height
Gewicht / Weight
01 Männlich / 01 male
02 Weiblich / 02 female
100------------200
20------------150
Normalgewicht / Normalweight
Übergewicht / Overweight
8. Energiesparmodus
Wenn Sie das Gerät 10 Minuten lang nicht benutzt
wurde, schaltet es sich automatisch in den
Energiesparmodus. Drücken Sie eine beliebige
Taste, um es wieder aufzuwecken.
)HKOHUPHOGXQJHQ
'LVSOD\]HLJWQLFKWVDQ²6WHOOHQ6LHVLFKHU
dass alle Kabel richtig verbunden sind.
(.DEHOORFNHURGHUGHIHNW6WHOOHQ6LH
sicher, dass alle Kabel richtig verbunden sind.
(.RQWUROOLHUHQ6LHREGLH6SDQQXQJXQWHU
50% der regulären Spannung ist. Kontrollieren Sie,
ob die Schalttafel schlecht riecht. Kontrollieren Sie
die Motorkabel.
(.HLQ*HVFKZLQGLJNHLWVVHQVRU²NRQWUROOLHUHQ
Sie, ob der Geschwindigkeitssensor richtig sitzt oder
verschmutzt ist. Löst dies das Problem nicht, lassen
Sie den Geschwindigkeitssensor austauschen.
(6WHLJXQJVIHKOHU²NRQWUROOLHUHQ6LHGDV
Steigungsmotorkabel oder setzen Sie den
Steigungsmotor zurück.
(hEHUVSDQQXQJRGHUQDFK5HSDUDWXU²
reinigen Sie das Laufdeck und das restliche Gerät,
fügen etwas Silikonöl unter der Laufmatte hinzu und
starten das Gerät neu.
(6FKDOWWDIHOGHIHNW²ODVVHQ6LHGLHVHHUVHW]HQ
0RWRUIXQNWLRQLHUWQLFKW²NRQWUROOLHUHQ6LHGLH
Motorkabel und den Leistungstransistor. Lassen Sie
diesen gegebenenfalls ersetzen.
7
