background image

PAGE 1 OF 7 

0922 IH-10152

H-10152

SANITAIRE

®

 WIDE TRACK 

INDUSTRIAL VACUUM

1-800-295-5510

uline.com

IMPORTANT! Read all instructions before using 
this vacuum.

WARNING! To reduce the risk of fire, electric 
shock or injury, basic precautions should be 
observed, including the following:

•  Connect to a properly grounded outlet only.  

See grounding instructions on page 2. Do not 
modify the three-prong grounded plug.

•  Do not leave vacuum when it is plugged in. Unplug 

from outlet when not in use and before servicing.

•  Do not use outdoors or on wet surfaces.

•  Do not use motorized nozzle on wet surfaces.

•  Do not allow to be used as a toy. Plastic film 

can be a suffocation hazard. Close attention is 

necessary when used by or near children.

•  Do not use for any purpose other than described in 

these instructions.

•  Do not use with damaged cord or plug. If vacuum 

is not working as it should, has been dropped, 

damaged, left outdoors or dropped into water,  
do not attempt to operate; have it repaired at an 
authorized service center.

•  Do not pull or carry by cord, use cord as a handle, 

close door on cord or pull cord around sharp 
edges or corners. Do not run vacuum over cord. 

Keep cord away from heated surfaces.

•  Do not unplug by pulling on cord. To unplug, grasp 

the plug, not the cord.

•  Do not handle plug or vacuum with wet hands.

•  Do not put any object into openings. Do not use 

with any opening blocked. Keep openings free of 
dust, lint, hair or anything that may reduce airflow.

•  Keep hair, loose clothing, fingers and all parts of 

body away from openings and moving parts of the 
vacuum and its accessories.

•  Turn vacuum off before plugging or unplugging.

•  Use extra care when cleaning on stairs.

•  Do not use to pick up flammable or combustible 

materials (lighter fluid, gasoline, kerosene, etc.) or 
use in areas where they may be present.

•  Do not pick up anything that is burning or smoking, 

such as cigarettes, matches or hot ashes.

•  Do not use without dust bag and/or filters in place.

•  Use only three-wire SJT extension cords that have 

three-prong grounding plugs and grounding 
receptacles that fit the vacuum plug.

•  Ensure extension cord is in good condition and is 

the correct size for your vacuum.

•  Maintain vacuum with care – inspect extension 

cords periodically and replace if damaged.

•  Do not turn your vacuum on until you are familiar 

with all instructions and operating procedures. 
Keep vacuum on a level surface.

•  Do not use vacuum in an enclosed space 

filled with vapors given off by oil-based paint, 
paint thinner, some moth-proofing substances, 
flammable dust or other explosive or toxic vapors.

•  Do not use to pick up toxic material (chlorine 

bleach, ammonia, drain cleaner, etc.).

•  Do not pick up hard or sharp objects such as glass, 

nails, screws, coins, etc.

SAFETY

TOOLS NEEDED

Phillips Screwdriver

3/8" Socket Wrench

Pliers

Summary of Contents for SANITAIRE H-10152








Reviews: