background image

PAGE 1 OF 7 

0219 IH-7862

π

  H-7862

HANDS DOWN 

HAND DRYER

1-800-295-5510

uline.com

PARTS

PRE-INSTALLATION WIRING

TOOLS NEEDED

Mounting Screw x 4

Wall Anchor x 4

Drill

8mm Drill Bit x 1

Wire Brush x 1

Wall Plate x 1

Mounting Display x 1

WARNING! For proper electrical connections, 
check the local building codes. The dryer must 
be installed by a qualified, licensed electrician.

Check that the electrical supply corresponds to that 

shown on the rating sticker on the hand dryer. If the 

hand dryer is connected to an electrical source other 

than what is stated on the rating sticker, permanent 

damage or improper, unsafe operation may result.
Make sure electricity is turned off at the main panel 

before installing, maintaining or cleaning the hand 

dryer. Dryer must be installed in accordance with the 

rules and applicable federal, state and local laws, 

including fire prevention.
Do not wire the hand dryer into the lighting circuit. It 

must be protected by an independent circuit.

The dryer is intended to be permanently connected to a 

power supply and must be properly grounded.

SAFETY

Troubleshooting and inside maintenance must be 

performed by a qualified service personnel.
Do not use power wash equipment to clean the dryer.

WARNING! Risk of electric shock. Do not 
remove the cover or attempt to repair unless 

qualified personnel are servicing the hand 
dryer. If the cover is removed or handled 

incorrectly, the internal elements of the 
hand dryer may cause damage or become 
permanently damaged.

Summary of Contents for H-7862








Reviews: