U-Line H-6501 Manual Download Page 1

PAGE 1 OF 9 

0721 IH-6501

π

  H-6501

HIGH-VISCOSITY 

ELECTRIC DRUM PUMP

1-800-295-5510

uline.com

SAFETY

GENERAL SAFETY 

This pump is designed to transfer clean, non-abrasive, 

and nonflammable liquids that are compatible with 

pump materials. 

For a list of materials and compatible chemicals, see 

uline.com.

Other factors such as viscosity, pressure, specific 

gravity, temperature, concentration and chemical 

combinations should also be considered when 

determining compatibility. Always contact your 

chemical supplier for compatibility recommendations. 

Final selection should be based on actual field testing 

under the conditions of intended use.

1.  Know the pump application, limitations and 

potential hazards.

CAUTION! Do not use to pump flammable 
or explosive fluids, such as gasoline, fuel 
oil, kerosene, etc. Do not use in explosive 
atmospheres. Pump should only be used with 

liquids compatible with pump component 
materials. Failure to follow this warning can 
result in personal injury and/or property 

damage.

2.  Make certain that the power source conforms to the 

requirements of the equipment.

3.  Provide adequate protection and guarding around 

moving parts.

4.  Disconnect power before servicing.

5.  Release all pressure within pump before servicing 

any component.

6.  Drain all liquids from pump before servicing.

7.  Secure the discharge line before starting the pump. 

An unsecured discharge line will whip, possibly 

causing personal injury and/or property damage.

8.  Before each use, check hoses for weak or worn 

condition, making certain that all connections are 

secure.

9.  Periodically inspect pump components. Perform 

routine maintenance as required.  

(See Maintenance section)

10.  Provide a means of pressure relief for pumps where 

discharge line can be shut off or obstructed.

11.  Personal Safety –

a.  Wear safety glasses at all times when working 

with pump.

b.  Wear a face shield and proper apparel when 

pumping hazardous chemicals.

12.  When wiring an electrically-driven pump, follow all 

electrical and safety codes, as well as the most 

recent United States National Electrical Code (NEC) 

and the Occupational Safety and Health Act (OSHA).

CAUTION! Risk of electrical shock! Never 
connect the green (or green and yellow) wire to 
a live terminal!

Para Español, vea páginas 4-6.

Pour le français, consulter les pages 7-9.

Summary of Contents for H-6501










Reviews: