background image

PAGE 3 OF 27 

0321 IH-1020

SYSTEM SET-UP

MACHINE PLACEMENT

Place the Automatic Stretch Wrap Machine close to 

an area where you will be wrapping your pallet loads. 

Make sure that there is sufficient room to load/unload 

the machine and that you do not stretch the wiring 

cable. Remember, you will need to provide electrical 

service to a 120 VAC, 15-AMP outlet.

FLOOR WEIGHT BEARING TOLERANCE

The floor must be able to bear the weight of the 

machine, the weight of the maximum load, plus a 

safety factor. The floor must also be able to tolerate 

the stress of the machine's operation. If fork trucks 

will operate on the same weight bearing area, add 

the weight of the trucks to the weight bearing stress 

tolerance requirements.

MACHINE SET-UP

1.  Place skidded machine close to the designated 

wrap area. Remove all shipping fasteners holding 

the machine to the pallet. The machine may be 

crated with the tower tilted down and the motor 

cover front carriage roller removed for shipping 

purpose.

2.  Place forks of the forklift through the tubes provided 

at the rear base of the module, remove the 

machine from skids and place it at the designated 

wrap area. 

3.  If the OPTIONAL ramp (H-1071) is purchased:  

 

Select a ramp position as illustrated below. The 

ramp can be positioned anywhere in a 180° 

rotation around the front of the turntable. There 

should be a 1/4

"

 gap between the turntable and 

the ramp. The ramp should be fully supported by 

the floor. (See Figure 1)

180˚

Figure 1

1/4" Gap

Summary of Contents for H-1020




























Reviews: