u-blox MAX-7 Series Hardware Integration Manual Download

Page: 53 / 55

MAX-7 / NEO-7 / LEA-7 - Hardware Integration Manual

GPS.G7-HW-11006-1

Appendix

Page 53 of 55

Appendix

Abbreviations

Abbreviation

Definition

ANSI

American National Standards Institute

CDMA

Code Division Multiple Access

EMC

Electromagnetic compatibility

EMI

Electromagnetic interference

EOS

Electrical Overstress

EPA

Electrostatic Protective Area

ESD

Electrostatic discharge

GLONASS

Russian satellite system

GND

Ground

GNSS

Global Navigation Satellite System

GPS

Global Positioning System

GSM

Global System for Mobile Communications

IEC

International Electrotechnical Commission

PCB

Printed circuit board

QZSS

Quasi-Zenith Satellite System

Table 19: Explanation of abbreviations used

Related documents

[1]

NEO-7 Data Sheet, Docu. No GPS.G7-HW-11004

[2]

MAX-7 Data Sheet, Docu. No GPS.G7-HW-12012

[3]

LEA-7N Data Sheet, Docu. No GPS.G7-HW-12039

[4]

u-blox 7 Receiver Description including Protocol Specification, Docu. No GPS.G7-SW-12001

[5]

u-blox 7 Firmware Version 1.0 Release Note, Docu. No GPS.G7-SW-12003

[6]

GPS Antenna Application Note, Docu. No GPS-X-08014

[7]

UBX-G7020 Data Sheet, Doc No GPS.G7-HW-10002

[8]

GPS Compendium, Doc No GPS-X-02007

[9]

I2C-bus specification, Version 2.1, Jan 2000,
http://www.nxp.com/acrobat_download/literature/9398/39340011_21.pdf

[10]

GPS Implementation and Aiding Features in u-blox wireless modules, Doc No GSM.G1-CS-09007-A3

All these documents are available on our homepage (http://www.u-blox.com).

For regular updates to u-blox documentation and to receive product change notifications please register
on our homepage (http://www.u-blox.com)

Summary of Contents for MAX-7 Series
























































Search results

Summary of Contents for MAX-7 Series

Reviews:

Related manuals for MAX-7 Series

Brands by name

Popular brands

u-blox MAX-7 Series, Hardware Integration Manual

Search results

Summary of Contents for MAX-7 Series

Reviews:

Related manuals for MAX-7 Series

Brands by name

Popular brands