background image

EVK-7 / EVK-8 / EVK-M8 User Guide 

 

UBX-14002502 - R10

 

Early Production Information

 

Device description

 

 

 

Page 10 of 25

 

 

Figure 3: EVK Label 

4.3.5

 

RST button 

The RST button on the front panel resets the unit. To avoid an inadvertent reset, the button is 
recessed. 

4.3.6

 

Safe boot button 

This is used to set the unit in safe boot mode. In this mode the receiver executes only the minimal 
functionality, such as updating new firmware into the SQI flash. In order to set the receiver in safe 
boot mode please follow these steps. 

1.

 

Press the BOOT button and keep holding  

2.

 

Press the RST button 

3.

 

Release the RST button  

4.

 

Release the BOOT button 

5.

 

If the UART interface has to be used, the training sequence has to be sent to the receiver. 
The training sequence is a transmission of 0x55 55 at the baud rate of 9600 Bd. Wait for at 
least 100 milliseconds before the interface is ready to accept commands. 

4.3.7

 

Slide Switch 

Use the slide switch on the front panel to choose between I2C (and UART) and SPI

 

communication 

ports. You must reset the unit by pressing the RST button when the slide switch has been changed. 

1.

 

I2C – In this selection the EVK operates with the UART (RS232 DB9 – rear panel or the 3.3 V 
level TxD (MISO), RxD (MOSI) at the front panel). Also the communication via 3.3 V DDC 
interface (I2C) is selected. 

2.

 

SPI – In this selection the EVK operates only with the SPI interface. RS232 (DB9) is switched 
off.

 

4.3.8

 

Test Connector 

This 14-pin test-connector provides additional functionality to the EVK, allowing access to the 
interface pins and an ability to measure the current used by the EVK. All pins are ESD protected. 

For accurate measurements, it is recommended to use a cable of at most 1 meter in length. Figure 
shows an example of a power supply connected to the test connector by using standard adapter 
cables from the manufacture Hirschmann. Figure  4  shows an example for overall current 
measurement. When connecting the 3.3 V digital interfaces RS232, SPI and DDC to your application, 
a cable length less than 25 cm is recommended.  

Summary of Contents for EVK-8


























Reviews: