Tysso POP-650-i User Manual Download Page 23

Page: 23 / 133

- 15 -

2.4. Embedded Receipt Printer

The POP-650 has embedded thermal receipt printer that is pre-installed into the base of the POS

system.

To install the paper roll into the printer:

2.4.1. Buttons & Indicators of Embedded Receipt Printer

Buttons

Paper Feed Button

Power Indicator

Error Indicator Paper

Indicator Printer

Power Switch

Paper Feed Button:

This function is to advance the paper.

Press the key and the paper advances by a

single line.

Press and hold the key for over 3 seconds

and the paper advances by multiple lines.

Power Switch:

Press to turn on the printer.

Control buttons & Indicators

Indicator Status

Indicator

Status

Description

Power

Power Off

Power On

Error

Printer Error (Out of paper, Printer head over heat, or
paper cutter error)

Paper

Out of paper
* The Error Indicator is lit as well

Summary of Contents for POP-650-i






































































































































Search results

Summary of Contents for POP-650-i

Reviews:

Related manuals for POP-650-i

Brands by name

Popular brands

Tysso POP-650-i, User Manual

Search results

Summary of Contents for POP-650-i

Reviews:

Related manuals for POP-650-i

Brands by name

Popular brands