TYROLIT Hydrostress WSE1621 Operating Instructions Manual Download

Page: 40 / 46

TYROLIT

Hydrostress AG

Page 40

WSE1621 Control unit

Faults

Fault

Possible cause

Solution

The control unit does not
work even though the
mains cable is connected

Control unit is switched off

Switch on the control unit

Defective mains cable

Replace the mains cable

No voltage at the power supply (build-
ing site)

Check power supply

Power supply phases incorrectly con-
nected

Check power supply

Phase missing

See the chapter entitled "Responding to displays"

The control unit starts and
then cuts out again

Power supply fuse at the building site
trips

Check the fuse and adjust if necessary

If necessary, change the power supply

See the chapter entitled "Responding to displays"

No power, even though
the control unit

is running

Incorrect voltage
Defective main motor

Make sure the voltage and frequency of the control unit
correspond to the specifications for the mains supply

Contact TYROLIT after-sales service

The control unit

cuts out

suddenly

Over- or undervoltage

Check the power supply. Refer to the error display

Cross section of power supply cable too
small

Check power supply

Defective plug connection

Check the plug connection

Check power supply

Group alarm

Refer to the error displays

Main motor is not running

• Main motor potentiometer is in 0 po-

sition

• Defective main motor On/Off switch

on remote controller

• Water On / Off switch is not in position

1 or it is defective

The remote controller ‘Ready’ light does
not illuminate

Contact TYROLIT after-sales service

Do not start the control unit

The EMERGENCY STOP is activated

Deactivating the EMERGENCY STOP function

Overheating

Check the water circuit and the plug-in couplings

Refer to the error displays

No water

Switch on the water supply

Refer to the error displays

Remote controller not
working

Rechargeable battery or batteries have
too little charge

Replace and recharge the rechargeable battery or install
cable operation

Replace the batteries

Feed potentiometer indi-
cates no function

• Defective potentiometer in the remote

controller

•  Feed motors not connected
•  Defective feed motor
•  Joystick is in the 0 position

Contact TYROLIT after-sales service

See the chapter entitled "Responding to displays"

Feed motor fails to build
up power

Remote controller potentiometer is de-
fective or in the 0 position

Contact TYROLIT after-sales service

Defective cable

Contact TYROLIT after-sales service

Defective motor

Contact TYROLIT after-sales service

Summary of Contents for WSE1621















































Search results

Summary of Contents for WSE1621

Reviews:

Related manuals for WSE1621

Brands by name

Popular brands

TYROLIT Hydrostress WSE1621, Operating Instructions Manual

Search results

Summary of Contents for WSE1621

Reviews:

Related manuals for WSE1621

Brands by name

Popular brands