background image

RECIRCULATING CHARCOAL FILTERS 

Chimney 

venl holes 

1

1

1

111

1

111

l

/

, 

A.ChImn叮加

A Roof cap 

B. 6" /15.2 cm) roond v

8. 6" (15.2 cm/ round V

l

It is recommended that the charcoal filter be replaced every 4-6 months. Charcoal filter replacements 

are available for purchase at:  www.cosmoappliances.com.  Charcoal Filter Kit Part# CFK1-TM 

13 

RANGE HOO

D

 OPERATIONS

14

Skip this step if you are installing a Ducted Range Hood. Charcoal Filters are 

only included with Ductless Models.

Capable of Vent-less or recirculation Operation, please install this charcoal 

carbon filter as picture.(NO NEED TO DISASSEMBLE THE VOLUTE)
Warning: if installed this charcoal filter to be ductless or recirculation mode, the 

noise would be more loudly, and the airflow would be less.

Control Panel Layout and Buttons Configurations: 

A.

Plus Button - used to increase settings.

B.

Minus Button - used to decrease settings.

C.

Timer - only works when the range hood fan is running, touch once, the timer

has a default setting of 15 minutes; use button A or B to increase or decrease

time duration depending on how much time you require.

D.

To press Light  to open or close the lamp. The luminance of lighting can be

adjusted from 0% to I 00% as wanted by touching Light .

E.

Auto Power off- press to tum off the fan automatically after 3 minutes.

F.

Power/Gesture Control—press to turn the control panel on/off; (the control

panel will power off automatically after I minute if no further operation) Press

and hold for 5 seconds will run (or turn off) the gesture control. Move your hand

from left to right side will run the l st fan speed, and again to go with 2nd fan

speed, then 3rd and 4th speed, and your 5th hand moving will bring the fan

 

into

sleeping. Oppositely, move your hand from right to left will decrease the fan

speed.

Remote control

Remote control 

sensor receives infrared(IR) signal from the 

Remote control

.

 

The maximum distance for IR data transmission is 3 meter(10ft.) and requires 

direct line

 of sight.The transmission distance may vary depending on 

temperature and 

remote control 

battery  condition.

12

13

Summary of Contents for KMC03-30










Reviews: