Tyco RDU Mk2 Installation & Programming Manual Download Page 148 | Manualshive

Page: 148 / 178

Tyco RDU Mk2 Installation & Programming Manual Download Page 148

RDU Mk2 Installation & Programming Manual

Document No: LT0499

Installation & Wiring

Page 8-18

8 April 2015

Issue 1.02

8.4

INSTALLATION : NZ DISPLAY EXTENDER BOARD &
BRIGADE DISPLAYS

8.4.1

GENERAL

The preferred method for remote brigade mimics in New Zealand is to use the LED-RZDU

–

refer LT0460.  The following information describes how remote NZ mimics have been
arranged using the RDU.

For New Zealand operation a Display Extender Board (PA0499 or PA0762) can be used if a
brigade mimic is needed or access to/display of any of the common signals is required.

In general, a separate display panel must be provided if there needs to be zone alarm
indication to the attending Fire Brigade staff.  The zone indicators inside the RDU cabinet or
RZDU do not meet the requirements of NZS4512, and viewing access to the cabinet by the
brigade members is generally not practical.

Any Ancillary Control Zone indicators on this external display must be coloured differently or
be segregated from the zone alarm and common indicators, and be clearly labelled.

There are several methods for providing a separate display panel.  Two basic approaches
are detailed below.

8.4.2

MIMIC DISPLAY

A mimic display uses the mimic outputs from the

RDU’s internal 16 Zone LED Indicator

Boards to drive alarm LEDs in an external display.  Each group of 16 zone alarms and the
common indicators are extended in a separate 26 way FRC to the external display.

The number of FRCs between the RDU and the external display limit the practical separation
distance.  Since the cabling is not supervised in any way, the Fire Service or approving
authority may place restrictions on this distance.  The cable must be well protected
mechanically by conduit, trunking or equivalent.

These parts are available for constructing displays of this type:

FP0475

FP,16 ZONE LED DISPLAY EXTENDER KIT (C/W LOOM)

FZ3031

16 ZONE LED DISPLAY EXTENDER KIT, RHS POSITION

LM0044

LOOM, DISPLAY EXTENDER FRC,2M,26 WAY

LM0045

LOOM, DISPLAY EXTENDER FRC,5M,26 WAY
(Longer and 3-way looms can be made to special order)

LM0092

LOOM, CONTROLLER TO FIRST DISPLAY, 1.2m

PA0483

PCB ASSY, IOR UNPROTECTED TERMINATION BOARD

PA0499

PCB ASSY, NZ DISPLAY EXTENDER BOARD

PA0769

PCB ASSY,16 O/P MIMIC TERMINATION BOARD,C/W RESISTORS
(As for PA0483 but 3k3 resister per output)

PA0753

PCB ASSY,PICTURE FRAME DISPLAY,16 LED MIMIC,24V

PA0760

PCB ASSY,NZ DISPLAY EXTENDER,PFD MIMIC

At the display panel there are two possibilities:

(i)

Geographic Plan Mimic - the FRCs from the RDU are connected to Termination
boards (PA0483). Individual LEDs with series resistors are mounted on the display
panel and wired to these Termination boards. Figure 8.4.1 shows this arrangement.

«
...
146
147
148
149
150
...
»

Summary of Contents for RDU Mk2



















































































































































































Reviews:

No comments