background image

Internet Alarm Communicator Installation Manual

Communications Reporting Codes

13

[021] Account Code

Default (FFFFFF)

The account code is included when transmitting any events generated by the Communicator. (e.g., Panel Absent Trouble). It is recom-
mended that the account code be the same as the control panel account number. Valid range: 00000

1

-FFFFF

E

. If 4 digit account codes

are needed the 2 lowest digits shall be programmed as FF.
(e.g., Account 1234 is programmed as:1234

FF

).

NOTE: 

Programming this Section with all 0 or F will cause a Module Configuration Trouble.

[022] Communications Format

Default (04)

Program 03 for Contact ID (CID). Program 04 for SIA. The module can be configured to send Events in SIA or CID format. The SIA
communication format follows the level 2 specifications of the 

SIA Digital Communication Standard - October 1997

. This format will

send the account code along with its data transmission. The transmission will look similar to the following at the receiver. Example:

Nri0 ET001

Where: 

N

 = New Event; 

ri0

 = Partition/Area identifier; 

ET

 = Panel Absent Trouble; 

001

 = Zone 001.

C

OMMUNICATIONS

 R

EPORTING

 C

ODES

[023] Panel Absent Trouble

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when communications with the panel have been lost for more
than 60 seconds.

[024] Panel Absent Trouble Restore

Default (FF)

Program 00 to disable this event or FF to enable. This event will occur when communications with the control panel have resumed.

S

YSTEM

 T

EST

 O

PTIONS

 [026 - 029]

Test Transmissions to Primary Receiver, with Backup to Secondary Receiver:

Set Ethernet Section [026] to (FF); [027] to (00). 
• If the test transmission fails to the primary receiver it will backup to the secondary receiver.
• If the test transmission fails to the secondary receiver an FTC trouble will be generated.

Test Transmission Unique to Primary and Secondary Receivers:

Set Ethernet Section [026] to (FF); [027] to (FF). 

45

5

WKST

West Kazakhstan Standard Time

PKT

Pakistan Time

YEKT

Yekaterinburg Time

UZT

Uzbekistan Time

TMT

Turkmenistan Time

TJT

Tajikistan Time

TFT

French Southern and Antarctic 

Time

MVT

Maldives Time

MAWT

Mawson Time

KGT

Kyrgyzstan Time

HMT

Heard and McDonald Island 

Time

DAVT

Davis Time

Table 6: Communications Reporting Codes

Event

SIA 

Identifier

SIA 

Reporting 

Code

CID

Qualifier

CID 

Event 

Code

CID 

Reporting 

Code

CID 

User/

Zone

[023] Panel Absent Trouble

ET

001

1

3

55

001

[024] Panel Absent Trouble Restore

ER

001

3

3

55

001

[026] Ethernet 1 Test Transmission

RP

001

1

6

A3

951

[027] Ethernet 2 Test Transmission

RP

002

1

6

A3

952

[030] FTC Restore

YK

001

3

3

54

001

Table 5: World Wide Time Zones

HEX

Value

Offset
Hours

Std

Abbrev

Location

HEX

Value

Offset
Hours

Std

Abbrev

Location

firealarmresources.com

Summary of Contents for DSC TL255

























Reviews: