background image

 

 

 

               http://www.TYAN.com 

 

1

 

 

 

QUAD CPU Card 

///

M4881 

Revision 1.00

 

 

      

Copyright © TYAN Computer Corporation, 2005-2006. All rights reserved. No part of this 
manual may be reproduced or translated without prior written consent from TYAN 
Computer Corp. 
 
All registered and unregistered trademarks and company names contained in this manual 
are property of their respective owners including, but not limited to the following. 
 
TYAN, QUAD CPU Cardsare trademarks of TYAN Computer Corporation. 
AMD, Opteron, and combinations thereof are trademarks of AMD Corporation. 
Nvidia and nForce are trademarks of Nvidia Corporation 
Phoenix BIOS is a trademark of Phoenix Technologies. 
Microsoft, Windows are trademarks of Microsoft Corporation. 
SuSE,is a trademark of SuSE AG. 
Linux is a trademark of Linus Torvalds 
IBM, PC, AT, and PS/2 are trademarks of IBM Corporation. 
Winbond is a trademark of Winbond Electronics Corporation. 
Broadcom

®

 is a trademark of Broadcom Corporation and/or its subsidiaries  

ATI and Rage XL are trademarks of ATI Corporation 
 
Information contained in this document is furnished by TYAN Computer Corporation and 
has been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability 
whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of 
TYAN products including liability or warranties relating to fitness for a particular purpose 
or merchantability. TYAN retains the right to make changes to product descriptions and/or 
specifications at any time, without notice. In no event will TYAN be held liable for any 
direct or indirect, incidental or consequential damage, loss of use, loss of data or other 
malady resulting from errors or inaccuracies of information contained in this document. 

 
 

 
 
 
 
 
 
 
 

Summary of Contents for M4881






























Reviews: