TVLogic TVC-FA301N Installation Manual Download Page 16 | Manualshive

Page: 16 / 20

background image

16

1. 232C-LAN cable connection diagram between the cameras.

(* It differs from normal network cable formation)

* If you only want to connect the camera using the network direct line, use the optional KTM-100.

1)

Configuration of camera and camera control line using 2 LAN cables

2) Using 1 LAN cable divided into 4 lines for camera and control line.

«
...
14
15
16
17
18
...
»

Summary of Contents for TVC-FA301N





















Reviews:

No comments

Related manuals for TVC-FA301N

Brand: FED Pages: 5

Brand: GE Pages: 2

Brand: Federal Signal Corporation Pages: 24

Brand: Dahua Pages: 20

Brand: jablotron Pages: 30

Brand: Z-Wave Pages: 6

Brand: Z3 Technology Pages: 5

Brand: Brickcom Pages: 40

Brand: Wiseup Pages: 24

Brand: ERNITEC Pages: 2

Brand: Perel Pages: 20

ITC215-PW4I-LZF27135

Brand: Dahua Pages: 109

NX-108E - Security NetworX NX-4 System

Brand: GE Pages: 20

Brand: UTL Pages: 2

Brand: NAPCO Pages: 4

LHWF1000 Series

Brand: Lorex Pages: 2

Calibration Pro

Brand: Buckleys Pages: 12

Brand: Axis Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands