background image

GENERAL DESCRIPTION

Attention!

The subject appliance must be installed only by qualified technical personnel in 

compliance with the standards. All connections must be rated for a single-phase 

power supply of 230V. For the disconnection from the power line, use an all-pole 

switch with contact with an opening of at least 3,5mm. Only suitable materials 

for the connections must be used to guarantee insulation that complies with 

current standards on the subject of electrical safety. The programmer carries 

out movement commands by radio; all the necessary safety devices are to be 

seen to separately.

Radio receiver, for DIN rail guide, with 10A 250 V

 relay contacts, transmitter 

channel memorization by means of an internal button or remote (via radio) using 

channel code addressing.

Centralised commands are possible allowing you to simultaneously switch on more 

than one appliance. Programmable relay functions: impulsive, ON/OFF and timer 

controlled up to 8 hours, 59 minutes and 59 seconds using internal buttons.

It can be commanded either by standard radio controls or directly through com-

mands sent from the TVLINK. The specific TVLINK codes are encoded directly by 

the manufacturer inside an EEprom memory module that maintains the information 

even in case of blackouts. They are also printed on the product label so they can be 

inserted into the TVLINK device. These codes cannot be cancelled or modified as 

they are an integral part of the receiver.

The transmitter code can be inserted (memorised) either directly into the receiver or via 

radio from the transmitter. The second possibility allows you to insert new transmit-

ters into an existing system without having to have the receiver on hand. This may be 

carried out easily by the user without the help of the installer whilst still guaranteeing 

the total secrecy of the code.

The user code is memorised under EEprom in the receiver which maintains the code 

information even when faced with blackouts.

Transmitters

The transmitters are encoded in the factory and each transmitter has its own unique 

code.

Caution! If you keep a channel button pressed down for more than 30 seconds the 

transmitter will automatically switch off.

The receiver is compatible with all transmitters of the TVLink range: TVTXV, 

TVTXP, TVTXC, TVTXK, TVTXQ, TVTXL, TVTXS...

SETTING THE IMPULSIVE, ON-OFF AND TIMER CONTROL FUNCTIONS

Attention

-Once you have entered the menu you cannot leave without altering the settings. 

The receiver will save the settings automatically 5 seconds after the last button was 

released.

1- To set the impulsive function (“IMPULSIVE”):

Press and hold down the “SET” button until the led “IMP” lights up. Release the 

button and wait until the led goes out (the led will go out five seconds after the button 

is released and the settings will be saved automatically).

In this way we have set an impulsive function.

2- To set the on-off function (“ON-OFF”):

Press the “SET” button twice and hold down until the “ON-OFF” led lights up. 

Release the button and wait until the led goes out (the led will go out five seconds 

after the button is released and the settings will be saved automatically).

In this way we have set an On-Off function.

3- To set the timer function (“SEC, MIN, HOU”):

To change the seconds, press the “SET” button three times and hold down until the 

“SECONDS” led lights up. At this point we can change the seconds by increasing 

them using the “MEM” button or decreasing them using the “DEL” button. Each 

time we press the “MEM or “DEL” button the led will go out and the value will be 

increased or decreased (e.g. 10 impulses correspond to 10 seconds). You can set from 

1 to 59 seconds, from 0 to 59 minutes and from 0 to 8 hours: Once you have reached 

the maximum of minimum limit the led will switch off and the value will no longer 

be increased or decreased.

After the seconds have been modified we can either wait for the led to go out and 

save the settings or we can modify the minutes and hours. 

To change the minutes press the “SET” button another time (within five seconds) 

until the “MINUTES” led lights up. At this point we can change the minutes by 

increasing them using the “MEM” button or decreasing them using the “DEL” 

button. After the minutes have been modified we can either wait for the led to go out 

and save the settings for the seconds and minutes or we can modify the hours. 

To change the hours press the “SET” button another time (within five seconds) until 

the “HOURS” led lights up. At this point we can change the hours by increasing 

them using the “MEM” button or decreasing them using the “DEL” button. After 

the hours have been modified we can either wait for the led to go out and save the 

settings for the seconds, minutes and hours or we can press “SET” again to modify 

“IMPULSIVE” or “ON-OFF” once more (see points 1 or 2).

Each time you enter the timer setting function the starting values for the seconds, 

minutes and hours are as follows: SEC=1, MIN=0, HOUR=0. 

If you have memorized the channel in couple, you can turn-off the relay with CH2 or 

CH4 before the set time.

4- Memorization

Attention!

 The first transmitter must be memorized using the receiver (each time you 

start a new installation you should cancel the entire memory content by pressing DEL 

in the receiver)

4.1- Memorisation single channel

The channels ch1,ch2,ch3,ch4 will be memorised one by one.

1- Press and hold down the pushbutton MEM of the receiver, the buzzer will sound 

continuously.

2- Transmit the channel which is to be memorised, once the channel is memorised, 

the buzzer will sound intermittently, release the pushbutton.

Repeat points 1 and 2 to memorise ulterior channels from receiver.

See paragraph 5 to memorise ulterior channels from transmitter.

4.2- Memorisation couple of channels

The channels ch1,ch2 and ch3,ch4 will be memorised in couple.

1- Press twice and hold down the pushbutton MEM of the receiver, the buzzer will 

sound continuously.

2- Transmit one of the couple of channel which is to be memorised, once the channel 

is memorised, the buzzer will sound intermittently, release the pushbutton.

Repeat points 1 and 2 to memorise ulterior channels from receiver.

See paragraph 5 to memorise ulterior channels from transmitter.

5- How to insert a transmitter via radio without having to access the receiver by 

means of an already memorized transmitter (memory indexing procedure)

The type of memorisation of  the channels (single, couple or 7-channel) depends on 

how the channel, whitch is used in point 4, has been memorized.

1) Press the button P3 located inside the already memorized transmitter. The enabled 

receiver sound continuously for 5 seconds. 

2) Transmit a channel present in the memory of the receiver, in which the new code is 

to be memorized, within 5 seconds  and the buzzer will interrupt the sound for 1 sec, 

and then carry on for another 5 seconds.

3) Transmit the new channel to be memorized within 5 seconds and once memorized 

the buzzer will sound intermittently.

To insert other transmitters another code repeat operations 1,2 and 3

If the receiver’s memory is full it cannot be enabled and this will be indicated by the 

buzzer B1 sounding intermittently.

6- To cancel a code with the push button DEL in the receiver

1)Press and hold down “DEL”, after 0.8 seconds buzzer will sound intermittently slowly.

2)Transmit  the code which is to be cancelled , once it has been cancelled, buzzer  will 

sound continuously. 

To cancel ulterior code repeat points 1 and 2.

6.1- To cancel all memorised coedes with the push button DEL in the receiver

1) Press and hold down “DEL” at least for 0.8 seconds, then buzzer  will sound slowly 

and intermittently. At this point release “DEL”  and press it again within 0.5 seconds, 

hold it down for at least 10 seconds ( during this period buzzer will sound intermittently 

and quickly)  as buzzer will sound continuously. Release the button after completing 

the operation.

6.2- To cancel via radio a code througt a trasmitter already set in the memory

 

Reviews: