Tusa TUL-400MDR User Manual Download Page 1

TUSA WATERPROOF FLASHLIGHT USER MANUAL

FEATURES

This stylish waterproof flashlight is compact yet bright, using a long life CREE-XPG LED for 

maximum effect.  The magnetic tail switch features variable power control: push one time 

for 100% power,  2 times for 30% power, 3 times for off.   From any setting,  push and hold 

switch for 3 seconds to activate emergency strobe.  The magnetic switch eliminates water 

leakage often seen in conventional models and has a high capacity to withstand pressure.

CAUTION: Make sure to only use equally charged batteries-do not mix and match. Never 

mix Alkaline and Lithium batteries.

SWITCH CARE: Because a magnet is used in the tail switch section, tiny naturally occurring

 

iron particles  (iron sand)  can accumulate on the switch during  diving.   After every dive, 

wash thoroughly in fresh running water to remove any such iron sand, as well as dirt and 

salt.  The  push button switch is designed  to allow water  to enter  switch area.   It  is very 

important to flush salt  water  from chamber.  Hold switch under flow of cool fresh water. 

Turn upside down and depress switch several times until no more water comes out. Repeat

 

process 2-3 times to ensure that all salt water is flushed from compartment.  Do not drop or 

place the flashlight on sand or dirt, since iron sand may stick or go into switch section. 

1)  Turn the  switch end cap at  the rear of  the  flashlight’s  body  counter-clockwise  and  remove  it.

2)  Slide out battery cradle and remove depleted batteries.

3)  Install (3) fresh AAA batteries into the cradle.  Follow the +/- polarity as shown.

4)  Clean by removing  any sand or dirt from screw  threads  and O-rings on switch end cap and then 

      apply a small amount of silicone grease on O-rings.

5)  Also check and clean (if necessary) the screw threads inside flashlight body.

6)  Slide the battery cradle back  into the flashlight  body, spring-end towards the flashlight head.

7)  Once  you  have  inserted the  battery cradle,  securely  tighten the switch end cap back into place 

      by turning clockwise.     

USAGE CAUTIONS

HOW TO REPLACE THE BATTERIES

Model# TUL-400MDR (wide beam) or TUL-410MBL (concentrated beam)

BODY

BATTERY CRADLE

SWITCH END CAP

SPECIFICATIONS

TUL-400MDR (wide beam)

 

  LED: CREE-XPG; 100,000 hour lifetime

  Battery: 3AAA

  Lumens: 165

  Beam angle: 50~60 degrees

  Magnetic tail switch: 100% - 30% - hold for strobe

  Burn time: 100% - 2 hours consecutive; 

                       30% - 7 hours consecutive

  Waterproof to 400 feet / 122 meters

  Net weight: 5.82 +/- 0.35 oz, 165 +/- 10g 

                          (without battery and hand strap)

  Dimensions: Φ(1.49 x 5.12) inches / (3.8 x 13) cm

  Use environment: 0-40 C° 

TUL-410MBL (concentrated beam

)

 

  LED: CREE-XPG; 100,000 hour lifetime

  Battery: 3AAA

  Lumens: 220

  Beam angle: 5~6 degrees

  Magnetic tail switch: 100% - 30% - hold for strobe

  Burn time: 100% - 2 hours consecutive; 

                       30% - 7 hours consecutive

  Waterproof to 400 feet / 122 meters

  Net weight: 5.82 +/- 0.35 oz, 165 +/- 10g

                          (without battery and hand strap)

  Dimensions: Φ(1.49 x 5.12) inches / (3.8 x 13) cm

  Use environment: 0-40 C°

Reviews: