turck TBEN-S2-4IOL Instructions For Use Manual Download Page 124

Page: 124 / 134

Operating

Using the data storage mode

124

Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com

IO-Link port diagnostics

PROFINET Diagnostics

Similar to port 1

IO-Link port 4

(Slot 5, according to configuration tool)

Similar to port 1

10.5

Using the data storage mode

Data storage mode

NOTE

Data storage mode is only available for devices complying with the IO-Link specifica-
tion V1.1.

In the IO-Link master, the data storage mode can be set using the parameter "data storage
mode".

00 = activated

01 = overwrite

10 = read in

11 = deactivated, clear

IO-Link-Master
(IOLM)

IO-Link-Device
(IOLD)

DS_UPLOAD_FLAG

Fig. 63: Data storage mode – general principle, Para. IOLD = parameters of the IO-Link device

A change of parameters in the device is indicated by the status of the DS_UPLOAD_FLAG bit:

0 = no changes in the device's parameter set

1 = changes in the device's parameter set (e. g. via DTM, at the device, etc.)

10.5.1

Parameter ”data storage mode” = read in

The data set in the device is

always

the reference data set.

The synchronization of the parameter sets is unidirectional towards to the master.

The status of the DS_UPLOAD_FLAG is ignored.

Summary of Contents for TBEN-S2-4IOL







































































































































Search results

Summary of Contents for TBEN-S2-4IOL

Reviews:

turck TBEN-S2-4IOL, Instructions For Use Manual, Page: 124 / 134

Search results

Summary of Contents for TBEN-S2-4IOL

Reviews: