turck TBEN-S2-4IOL Instructions For Use Manual Download Page 121

Page: 121 / 134

V01.00 | 2019/10

121

10.4.2

Diagnostic telegram

Channel Byte no.

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

DXP

DXP diagnostics

ERR DXP7 -

ERR DXP5 -

ERR DXP3 -

ERR DXP1 -

IO-Link

Device diagnostic messages

Master diagnostics

IO-Link
port 1

EVT1

EVT2

PDINV

HWERR

DSERR

CFGERR

PPE

GENERR

OLV

VHIGH

VLOW

ULVE

LLVU

OTEMP

PRMERR

IO-Link
port 2

2…3

Assignment similar to IO-Link port 1

IO-Link
port 3

4…5

IO-Link
port 4

6…7

NOTE

The “process data” invalid diagnostic (PDINV) can be sent from both devices, IO-Link
master or IO-Link device.

Meaning of diagnostic Bits

Bit

Meaning

DXP diagnostics

ERR_DXPx

Overcurrent at the output (if the DXP channel is used as output)

IO-Link master diagnostics

CFGER

Wrong or missing device
The connected device does not match the channel configuration or there is no
device connected to the channel. This diagnostic message depends on the para-
meterization of the channel.

DSER

Data storage error
Possible causes:

Data storage mismatch:
IO-Link device in accordance with IO-Link V1.0 connected.
The data storage buffer contains data of another device.

Overflow of the data storage buffer

The connected device may be locked for parameter changes or for data stor-
age.

Summary of Contents for TBEN-S2-4IOL







































































































































Search results

Summary of Contents for TBEN-S2-4IOL

Reviews:

turck TBEN-S2-4IOL, Instructions For Use Manual, Page: 121 / 134

Search results

Summary of Contents for TBEN-S2-4IOL

Reviews: