manualshive.com logo in svg

turck TBEN-LH-8IOL, Configuration Manual, Page: 33 / 48

Share
Download
turck TBEN-LH-8IOL Configuration Manual Download Page 33

 
 
 

 

 

33 

4  Configure TBEN-LH-8IOL with Rockwell PLC 

The configuration of the TBEN-LH with the Logix5000 controllers, using RSLogix5000 / Studio5000 
programming environment may be done using: 
 

 

EDS file 

 

Generic device profile 

 

4.1  TBEN-LH-8IOL Configuration using EDS files 

4.1.1  Install EDS file 

The EDS file is the Electronic Data Sheet or the device configuration file, described in the  
“Volume 1, Common Industrial Protocol (CIP), Edition 3.22, by ODVA”. 
The procedure: 

  Download 

TBEN-LH-8IOL_R2.7.EDS

 file from the TURCK web site 

  In the RSLogix5000  menu bar, expand the 

Tools

 drop down menu and click on the 

EDS 

hardware Installation Tool 
 

 

Figure 4.1 – Tools menu 

 

  In the 

Rockwell Automation’s EDS Wizard 

 dialog, click at the 

Register and EDS file(s) 

 and 

Next

 

  Follow the dialog to complete device registration 

 

 

Figure 4.2 – Register an EDS file(s) 

Summary of Contents for TBEN-LH-8IOL

















































Reviews:

No comments