Tsurumi Pump 100C222 Operation Manual Download Page 1 | Manualshive

Page: 1 / 19

background image

17236427/B-10008-11

INTRODUCTION

Thank you for selecting the Tsurumi C Submersible Sewage & Wastewater Pumps.

This equipment should not be used for applications other than those listed in this manual. Failure to observe

this precaution may lead to a malfunction or an accident. In the event of a malfunction or an accident, the

manufacturer will not assume any liability. After reading this Operation Manual, keep it in a location that is

easily accessible, so that it can be referred to whenever information is needed while operating the equipment.

CONTENTS

1. BE SURE TO READ FOR SAFETY  ............................... 1
2. PART NAMES.................................................................. 4
3. PRIOR TO OPERATION   ............................................... 4
4. INSTALLATION   ............................................................. 5
5. ELECTRICAL WIRING .................................................... 8
6. OPERATION ....................................................................12
7. MAINTENANCE AND INSPECTION ...............................15
8. DISASSEMBLY AND REASSEMBLY PROCEDURE ......17
9. TROUBLESHOOTING   ..................................................18

TSURUMI MANUFACTURING CO., LTD.

Submersible Sewage & Wastewater Pumps

OPERATION MANUAL

with Cutter Impeller

C Series

1
2
3
...
»

Summary of Contents for 100C222




















Reviews:

No comments

Related manuals for 100C222

Brand: Bacharach Pages: 12

Brand: Nachfolger Pages: 2

Brand: Navien Pages: 48

Brand: Navien Pages: 2

TriScroll 300 Series

Brand: Varian Pages: 19

Brand: Walrus Pages: 3

Brand: Walrus Pages: 5

Brand: Oerlikon Barmag Pages: 36

Ingenio VM 050 D400-3-E

Brand: Atlantic Pages: 69

Brand: Chiltrix Pages: 54

Brand: Edwards Pages: 16

Brand: RadonAway Pages: 22

Brand: samhydraulik Pages: 7

ACT Signature Series

Brand: Aqua Comfort Pages: 2

Brand: Trane Pages: 8

Brand: InSinkErator Pages: 16

Clean Jet 800 Plus + Kit

Brand: T.I.P. Pages: 140

SUNLINE 2000 BP 072

Brand: Unitary products group Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands