background image

 

 

1 Notes on this Manual 

  1.1 Scope of Validity 

The User Manual describes system configuration and detailed procedures for installation, 

operation and maintenance of TSOL-B100E-S Series Inverter Battery. However, this 

manual does not include any information about inverters that the battery may be applied 

to. Please read the User Manual before using this product.

 

1.2 Target Group 

This manual is for qualified electricians. The tasks described in this manual only can be 

performed by qualified personnel. 

1.3 Symbols Used 

The following types of safety instructions and general information appear in this 

document as described below: 

 

 

 

 

 

 

 

Danger

 

“Danger” indicates a hazardous situation which, if not avoided, will result in 

death or serious injury. 

Warning

 

“Warning” indicates a hazardous situation which, if not avoided, could result 

in death or serious injury. 

Caution

 

“Caution” indicates a hazardous situation which, if not avoided, could result 

in minor or moderate injury. 

Note

 

“Note” provides tips that are valuable for the optimal operation of our 

product. 

Summary of Contents for TSOL-B100E-S



















Reviews: