TSI Instruments 3082, Operation And Service Manual

Page: 215 / 225

Computer Interface C-9
Table C-2
Electrostatic Classifier Firmware Commands List (select)
Command Title Description
WSCONTROL Write Control of
Classifier WSCONTROL sets who has control with AIM, OPEN, or GUI.
Example: WSCONTROL OPEN sets to classifier control
WSGPIODIGOUT0 Write GPIO
Digital Output 0 WSGPIODIGOUT0 sets the GPIO output to 0 or 1.
Example: WSGPIODIGOUT0 1 turns the output on, 0 turns the output
off.
WSGPIODIGOUT1 Write GPIO
Digital Output 1 WSGPIODIGOUT1 sets the GPIO output to 0 or 1.
Example: WSGPIODIGOUT1 1 turns the output on, 0 turns the output
off.
WSSCANPARAM Write SMPS
Scan Parameters WSSCANPARAM sets the following scan parameters:
tres , time resolution in milliseconds, fixed at 20 ms.
tlow , time DMA voltage held at vmin in milliseconds, 0 to 10000 ms
tup , time DMA voltage is ramped up in milliseconds, 0 to 300000 ms
thigh , time DMA voltage held at vmax in milliseconds, 0 to 10000 ms
tdown , time DMA voltage ramped down in milliseconds, 0 to 300000 ms
vmin , starting DMA voltage, 1.0 to 100000.0 v
vmax , ending DMA voltage, 1.0 to 10000.0 v
pol , polarity of DMA voltage, where -1 = negative voltage, 0 = detectors
with no voltage, 1 = DMA voltage
Example: RSSCANPARAM 20,500,10000,500,1000,13.1,9456.0,-1 will
have a voltage of 13.1 to 9456 over the tup time of 10 seconds
WSPARTICLEDIAM Write Classifier
Particle Diameter WSPARTICLEDIAM sets the particle diameter setpoint.
Example: WSPARTICLEDIAM 100 sets the particle diameter to 100.
WSDMAMN Write DMA
Model Number WSDMAMN sets DMA model number. Saves to EEPROM on bottom of
3082-compatible DMA. Should be followed by a
DOSAVEDMAEEPROM.
Note that the suffix “A” is not used.
Example: WSDMAMN 3085 sets model number to 3085.
WSDMASN Write DMA Serial
Number WSDMASN sets DMA serial number. Saves to EEPROM on bottom of
3082-compatible DMA. Should be followed by a
DOSAVEDMAEEPROM.
Example: WSDMASN 3085114501 sets DMA s/n to 3085114501.
WSDMALENGTH Write DMA
Length WSDMALENGTH sets DMA length, in meters. Used by inversion
algorithm. Saves to EEPROM on bottom of 3082-compatible DMA.
Should be followed by a DOSAVEDMAEEPROM.
Example: WSDMALENGTH 0.44369 sets DMA length to 44.369 cm.
WSDMAID Write DMA Inner
Diameter WSDMAID sets DMA inner diameter, in meters. Used by inversion
algorithm. Saves to EEPROM on bottom of 3082-compatible DMA.
Should be followed by a DOSAVEDMAEEPROM.
Example: WSDMAID 0.01874 sets DMA inner diameter to 1.874 cm.
WSDMAOD Write DMA Outer
Diameter WSDMAOD sets DMA outer diameter, in meters. Used by inversion
algorithm. Saves to EEPROM on bottom of 3082-compatible DMA.
Should be followed by a DOSAVEDMAEEPROM.
Example: WSDMAOD 0.03922 sets DMA outer diameter to 3.922 cm.
WSDMATYPE Write DMA Type WSDMATYPE sets the DMA type to 1 (cylindrical) or 2 (radial). Used by
inversion algorithm. Saves to EEPROM on bottom of 3082-compatible
DMA. Should be followed by a DOSAVEDMAEEPROM.
Example: WSDMATYPE 1 sets DMA type to cylindrical.
WSCUSTOMDMALENGTH Write Custom
DMA Length WSCUSTOMDMALENGTH sets length of custom DMA, in meters. Used
by inversion algorithm. Should be followed by a DOREGSAVE.
Example: WSCUSTOMDMALENGTH 0.44369 sets custom DMA length
to 44.369 cm.