Tryton TJV10AL, Operating Instruction

Page: 6 / 52

6
Using the charger: Fig.G
a) Use only dedicated power adapters to charge the battery.
Application of a power adapter dedicated to charge another type of the
battery unit poses a risk of fires.
b) The supplied charger should only be used for charging batteries
that are supplied together with it.
Charging other batteries may
cause breaking and disintegration of the battery, bodily harm, or fire.
c) Do not disassemble the charger.
d) The charger is designed exclusively for indoor use. It must not be
exposed to water or moisture.
e) Charge only in an ambient temperature between 15-25
degrees.
f) Do not insert metal objects of any kind into the charger.
The device is dedicated to drive in and out screws, drilling boreholes in such
materials as steel, wood, plastics, etc.
The combo drill and screwdriver is designed exclusively for DIY applications
.
device
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values given.
The above-mentioned causes may lead to higher exposure to vibrations
during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
work tools, assurance of proper hand temperature, or determination of the
sequence of work operations.
n
The declared total vibrations and declared noise emissions were measured
ź
Cordless drill/S crewdriver -
in accordance with a standard test method and may be used for tool
-
comparison.
ź
Battery TJ15AK -
The declared total vibrations and noise emissions can be used in preliminary
Operating instruction-
exposure assessment.
Warnings:
n
The vibrations and noise emissions during the actual use of the power tool
Fig.A 1. Keyless chuck
may differ from the declared values depending on how the tool is used and
2. Clutch control knob on the type of the workpiece in particular.
3. Gear shifter
Determine safeguards to protect the operator. They should be based on the
estimated exposure under actual operational conditions (taking into
4. Rotation direction switch
account all parts of the operating cycle such as when the tool is switched off
5. Fastener to hang on the belt
or idle except the start time).
6.
7.
Battery
8. Battery lock clip
9. On/off switch
10. Auxiliary lighting
Fig.C
n
Charging the battery
The driver is supplied with a partially charged battery.
Battery indicator to show the battery status of charge
Fig.F
Charge the battery fully before use.
APPLICATIONS AND CONSTRUCTION:
Despite using the tool according to its intended application it is impossible
to eliminate certain residual risk factors. Considering the tool construction
the following risks may occur when operating the tool:
- Touching the rotating drill bit with the hand
operator's clothes .
- Burns when changing drill bits (Drill bits heat up intensely during
operation; use protective gloves when changing the drill bit).
- Throwing back machined object or its fragment.
- Bending/breaking the drill.
The set includes:
Device components (see page 2 ) :
TECHNICAL PARAMETERS:
The tool must not be used for work requiring a professional tool.
Any use of the that is not in observance with the above-mentioned
purpose is forbidden, leads to the loss of warranty, and relieves the
manufacturer from responsibility for the resulting damage.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the surroundings.
or
1pc.
1szt.
1pc.
ź
1pc.
ź
Warranty card - 1 pc.
PREPARATION FOR WORK:
Prior to each use of the tool one has to check whether moving parts of the
device are in operating conditions, not seized, cracked or damaged that may
affect proper operation of the tool. Damaged tools must be handed over for
repairs before they can be used again.
Battery level indicator button
You can check the
battery level with the battery level indicator button ( 13 ). A single LED
means the battery level is low, two LEDs mean medium level, and three LEDs
mean full battery.
The first charging
17. Left-threaded fixing screw
ź
Charger TJ3LD
Strap for hanging on hand
11. Charger
12. Adapter
13.
14.
15. Clutch setting indicator
16. Drilling setting pictogram
Rotation speed under no-load conditions ( Gear I/II)
Supply voltage
Chuck clamping range
Gear shifter I-II
Maximum torque
Maximum drilling
diameter
Wood
Steel
Acoustic pressure level (LpA)
Acoustic power (LwA)
Vibration level according to EN 60745, drilling a
h, D
Weight (with battery)
( K=1,5 m/s²) T olerance of measurements
Battery type Li-ion
Battery charging voltage
Charging time
Charger power voltage
n =0-350 / 0-1300/min
o
20 V d.c.
yes
1 1 0- 2 4 0V, 50 -60 Hz
3-5 h
20 V
2
1,746 m/s
99,9 dB(A)
89,9 dB(A)
1,4 kg
13 mm
25 mm
ø
0,8-10 mm
25 Nm
Battery capacity 1,5 Ah
T olerance of measurements K K
LpA, LwA
3 dB(A)