background image

20V

7

Start Up

General remarks for using the battery

Installing and Removing the Battery

• Set the direction button in the locked position (center).

• Hold the Chuck base firmly with one hand and with the 

other hand turn the tip of the chuck counter clockwise, so 

that the jaws loosen.

• Insert the bit until it stops or remove it whichever the 

situation.

• Turn the drill bit clockwise to secure the drill bit. The drill bit 

is equipped with a retention lock that is activated by turning 

the drill bit, once the drill bit is secured; a click will be heard.

Bits or adaptors assembly

Jaws

ENGLISH

• To bore and screw release the switch and and press the direction 

button on the side where marks point towards the chuck.

• To reverse the turn, and unscrew press it on the other side.

• The drill switch will get blocked if the button sits in the middle.

                          • The first time you turn on the drill and after 

reversing rotation you might hear a click. This in normal and 

does not represent a problem.

                          • To prevent damaging the tool, never reverse 

the rotation direction while the drill is running. 

Direction of rotation

CAUTION

CAUTION

Torque

regulator

• To select the desired torque level to screw drive, turn the torque 

regulator until it matches the corresponding number with the upper mark:

From 1 to 4 for small screws,

From 5 to 9 for screws on soft materials,

From 10 to 15 for screws on soft and hard material

On 16 to 21, for larger screws.

• To bore metal, wood or plastic turn the torque regulator into the 

ROTATION  (        ) position.

                          • The torque level necessary depends on the type of 

screw to be used and the material onto which you are working.  If in 

doubt use a lower torque and increase gradually until reaching the right 

one.  An adequate torque prevents damaging the tool. 

Torque Adjust

CAUTION

The battery is shipped NOT CHARGED.  It is necessary to charge the battery approximately 1 hour before being able to use it.   

The normal charge is 32 °F to 113 °F.  When not in this level the charge automatically stops until reaching the right temperature.  

The normal temperature for discharge / work is 32 °F to 167 °F. If 167 °F are exceeded, the electronic control stops the tool 

energy until the temperature reaches the temperature optimum new level. When the battery is below the normal tension while 

working the tool stops working. Give the tool 15 minutes rest. In warm weather or after a long period of work the battery will get 

too hot to recharge. Allow the battery to cool down before trying to charge again.

To install the battery into the tool handle, align the battery unit with the rails 

on the inside of the tool handle and slide it into the handle until the battery 

unit is firmly inserted into the tool; check that it does not slip out by itself. 

To remove the battery from the tool, press the release button (

C

) and pull 

the battery firmly out of the tool handle.

Chuck

• The two speeds in the drill work in a similar manner to those 

used in cars.

• Low speed (

1

) will give a lot of torque (torsion power). Use this 

speed when starting to drill large orifices, be it wood or metal. This 

will prevent the bit to get stuck.

• High speed (

2

) has a reduced torque but lets the drill operate 

with higher revolutions per minute, that make the tool when in 

the drill function to bore faster lean metal or wood.

Speed selection

Forward

Reverse

C

Summary of Contents for 101404

























Reviews: