13
Technical data
determined in accordance with EN 624 or Truma test conditions
Type of gas:
Liquid gas
(propane/butane)
Operating pressure:
30 mbar (28 mbar for butane/37 mbar for propane) or 50 mbar
(see manufacturer’s plate)
Rated thermal output:
3400 W
Gas consumption:
30 – 280 g/h
Operating voltage
heater: 1,5 V
fan: 12 V
Power consumption
heater: 50 mA (ignition), 0,01 mA (monitoring)
fan: 0,3 bis 1,0 A
Air flow rate:
up to 135 m
3
/h (with fan duct ÜR dia. 65 mm)
up to 142 m
3
/h (with fan duct VR dia. 72 mm)
Weight:
18,5 kg (with front case and fan )
Declaration of conformity:
The liquid gas heater Trumatic S 3002 FS has been approved
by the DVGW and complies with the EC guidelines
(90/396/EWG) for gas appliances as well as with the associated
EC guidelines. The product ID No. for EU countries is:
CE-0085AP0325
EEC Type Approval:
e1 022603
The right to effect technical modifications is reserved!
Dimensions:
510 mm
713 mm
210 mm
240 mm
167
ca. 582 mm
ca. 72 mm
280 mm
375 mm
320 mm
45 mm
Ø 73
Manufacturer’s terms of warranty
1. Case of warranty
The manufacturer grants a warranty for malfunctions in the
appliance which are based on material or production faults. In
addition to this, the statutory warranty claims against the seller
remain valid.
A claim under warranty shall not pertain
– for parts subject to wear and in cases of natural wear and
tear,
– as a result of not original Truma parts being used in the appli-
ance and as a result of unsuitable gas pressure regulators
being used,
– as a consequence of failure to respect Truma instructions for
installation and use,
– as a consequence of improper handling,
– as a consequence of improper transport packing, not
arranged by Truma.
2. Scope of warranty
The warranty is valid for malfunctions as stated under item 1,
which occur within 24 months after conclusion of the pur-
chase agreement between the seller and the final consumer.
The manufacturers will make good such defects by subse-
quent fulfilment, i.e. at their discretion either by repair or re-
placement. In the event of manufacturers providing service
under warranty, the term of the warranty shall not recom-
mence anew with regard to the repaired or replaced parts;
rather, the old warranty period shall continue to run. More ex-
tensive claims, in particular claims for compensatory damages
by purchasers or third parties, shall be excluded. This does not
affect the rules of the product liability law.
The manufacturer shall bear the cost of employing the Truma
customer service for the removal of a malfunction under war-
ranty – in particular transportation costs, travelling expenses,
job and material costs, as long as the service is carried out in
Germany. Customer service carried out abroad is not covered
by the warranty.
Additional costs based on complicated removal and installation
conditions of the appliance (e.g. removal of furniture or parts
of the vehicle body) do not come under warranty.
3. Raising the case of warranty
The manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG,
Wernher-von-Braun Strasse 12,
D-85640 Putzbrunn.
In Germany, in the event of faults the Truma Service Centre
should in principle be contacted; abroad, the individual service
partners are available (see address list). Any complaints are to
be described in detail. In addition, the properly completed
guarantee certificate is to be presented, or the factory number
of the unit and the date of purchase given.
In order for the manufacturers to be able to determine whether
an incident subject to guarantee has occurred, the end user
must, at his own risk, bring the device to the manufacturers or
send it to them. If there is damage to heaters (heat exchang-
ers), the gas pressure regulator must also be sent back to the
factory.
In instances of the device being sent to the works, dispatch is
to be effected by freight transport. In cases under guarantee,
the works shall bear the transport costs or the costs of delivery
and return. If the damage is deemed not to be a warranty case,
the manufacturer shall notify the customer and shall specify re-
pair costs which shall not be borne by the manufacturer; in this
case, the customer shall also bear the shipping costs.
