manualshive.com logo in svg

Trox Technik FKRS-EU, Installation And Operating Manual

For the Trox Technik FKRS-EU product, make sure to refer to the Installation And Operating Manual for detailed instructions on setup and use. This manual can be downloaded for free from our website. Ensure a smooth experience with this high-quality product by following the guidelines provided in the manual. Download now at manualshive.com.

Share
Download
background image

5.3.1.3 

Installation kit TQ / TQ2

Installation kit TQ / TQ2 for dry mortarless installation into walls

The installation kit TQ is an integral component of the fire damper and must be ordered together with the

damper.

The installation kit TQ2 is supplied separately and must be installed by the customer.

The installation kit can also be supplied subsequently and mounted on the fire damper.

Fig. 23: Supply package and installation of installation kit TQ2 for dry mortarless installation

1

FKRS-EU

2.11

Installation kit TQ2, consisting of:

a

Half-shell 1

b

Half-shell 2

c

Bracket

d

Intumescent seal (2 strips)

Installation of installation kit TQ2

1.

Lay half-shells (2.11a) and (2.11b) of the installation kit (2.11) around the FKRS-EU and fix with two brackets

(2.11c) (installation position of the FKRS-EU as required).

2.

Affix intumescent seal (2.11d).

Installation

General installation information  > Installation block and installation kits

 

Fire damper Type FKRS-EU

36

Summary of Contents for FKRS-EU

















































































































































































Reviews:

No comments

Related manuals for FKRS-EU

Brands by name

Popular brands

Load more brands