background image

10.3  Inspection, maintenance and repair measures

Interval

Measure

Staff

A

Access to the fire damper

Internal and external accessibility

Provide access

Specialist per-

sonnel

Installation of the fire damper

Installation according to operating manual

Install the fire damper correctly.

Specialist per-

sonnel

Transport and installation protection, if any

Transport/installation protection has been removed

Remove transport/installation protection

Specialist per-

sonnel

Connection of ductwork/cover grille/flexible connector

Connection according to this manual

Establish correct connection

Specialist per-

sonnel

Power supply to the spring return actuator

Power supply according to spring return actuator rating plate

Provide correct voltage

Skilled qualified

electrician

A / B

Check fire damper for damage

Fire damper, damper blade and seal must be intact

Replace the damper blade

Repair or replace the fire damper.

Specialist per-

sonnel

Function of the release mechanism

Function OK

Fusible link intact/no corrosion

Replace the fusible link

Replace the release mechanism

Specialist per-

sonnel

Functional test of the fire damper (with fusible link) 

Ä

  160

Fire damper can be opened manually

Handle can be locked in the OPEN position

Damper blade closes when triggered manually

Determine and eliminate the cause of the fault

Repair or replace the fire damper.

Replace the release mechanism

Specialist per-

sonnel

Functional test of the fire damper (with spring return actuator) 

Ä

  161

Actuator function OK

Damper blade closes

Damper blade opens

Determine and eliminate the cause of the fault

Replace the spring return actuator

Repair or replace the fire damper.

Specialist per-

sonnel

Function of external duct smoke detector

Function OK

Fire damper closes when triggered manually or when smoke is detected

Fire damper opens after reset

Determine and eliminate the cause of the fault

Repair or replace duct smoke detector

Specialist per-

sonnel

Maintenance

Inspection, maintenance and repair measures 

 

Fire damper Type FKRS-EU

167

Summary of Contents for FKRS-EU

















































































































































































Reviews: