manualshive.com logo in svg

Trox Technik FKRS-EU, Installation And Operating Manual

For the Trox Technik FKRS-EU product, make sure to refer to the Installation And Operating Manual for detailed instructions on setup and use. This manual can be downloaded for free from our website. Ensure a smooth experience with this high-quality product by following the guidelines provided in the manual. Download now at manualshive.com.

Share
Download
background image

5.12  Solid wood ceilings

5.12.1 

Mortar-based installation into solid wood ceilings

Fig. 126: Mortar-based installation into a solid wood ceiling, suspended or upright

1

FKRS-EU

2.1

Mortar

4.5

Solid wood ceiling

7.19

Fire-resistant cladding

9.2

Extension piece or duct

 – 

Up to EI 90 S

Additional requirements: mortar-based installation into solid wood ceilings

Solid wood ceiling 

Ä

  33

≥

 75 mm distance from fire damper to load-bearing structural elements

≥

 200 mm distance between two fire dampers in separate installation openings

Structural and fire resistance properties of the ceiling construction, including the attachment to the concrete or

any required reinforcement, have to be evaluated and ensured by others.

Installation

Solid wood ceilings  > Mortar-based installation into solid wood ceil...

 

Fire damper Type FKRS-EU

146

Summary of Contents for FKRS-EU

















































































































































































Reviews:

No comments

Related manuals for FKRS-EU

Brands by name

Popular brands

Load more brands