Trox Technik FKRS-EU Installation And Operating Manual Download Page 135

Page: 135 / 176

5.11.5

Mortar-based installation into ribbed ceilings

Fig. 116: Mortar-based installation into ribbed ceilings, shown upright (also applicable for suspended arrangement)

FKRS-EU

2.2

Concrete

4.9

Reinforced ribbed ceiling*

9.2

Extension piece or duct

Up to EI 90 S

Illustration representative, other ceiling construc-

tions possible according to local conditions and

ceiling manufacturers

Additional requirements: mortar-based installation into ribbed ceilings



Ribbed ceiling, see



Concrete bases H < 150 mm do not require reinforcement



≥

40 mm distance from fire damper to load-bearing structural elements



≥

45 mm distance between two fire dampers

Structural and fire resistance properties of the ceiling construction, including the attachment to the concrete or

any required reinforcement, have to be evaluated and ensured by others.

Installation

Solid ceiling slabs > Mortar-based installation into ribbed ceilings

Fire damper Type FKRS-EU

135

Summary of Contents for FKRS-EU

















































































































































































Search results

Summary of Contents for FKRS-EU

Reviews:

Related manuals for FKRS-EU

Brands by name

Popular brands

Trox Technik FKRS-EU, Installation And Operating Manual

Search results

Summary of Contents for FKRS-EU

Reviews:

Related manuals for FKRS-EU

Brands by name

Popular brands