manualshive.com logo in svg

Trox Technik FKRS-EU, Installation And Operating Manual

For the Trox Technik FKRS-EU product, make sure to refer to the Installation And Operating Manual for detailed instructions on setup and use. This manual can be downloaded for free from our website. Ensure a smooth experience with this high-quality product by following the guidelines provided in the manual. Download now at manualshive.com.

Share
Download
background image

5.7.3  Installation remote from solid wood walls with mineral wool

Fig. 92: Mortar-based installation remote from a solid wood wall or CLT wall

1

FKRS-EU

2.1

Mortar

3.11

Solid wood wall / CLT wall

6.29

Mineral wool Paroc Hvac Fire Mat 80BLC

(80 kg/m³)

6.30

Reinforcing board mineral wool

Paroc Hvac Fire Mat 80BLC (80 kg/m³), glued all

round

9.2

Sheet steel duct

Up to EI 60 S

Fig. 93: Dry mortarless installation remote from a solid wood wall or CLT wall, with a fire batt

1

FKRS-EU

3.11

Solid wood wall / CLT wall

6.7

Fire batt

6.29

Mineral wool Paroc Hvac Fire Mat 80BLC

(80 kg/m³)

6.30

Reinforcing board mineral wool

Paroc Hvac Fire Mat 80BLC (80 kg/m³), glued all

round

7.11

Trim panels, single-layer, fire-resistant

8.21

Acrylic or sealing compound (suitable for fire batt

system)

9.2

Sheet steel duct

Up to EI 60 S

Additional requirements: installation remote from solid wood walls with mineral wool

Solid wood wall or CLT wall 

Ä

  33

Paroc mineral wool, see 

Ä

  27

Installation

Solid wood walls  > Installation remote from solid wood walls with...

 

Fire damper Type FKRS-EU

110

Summary of Contents for FKRS-EU

















































































































































































Reviews:

No comments

Related manuals for FKRS-EU

Brands by name

Popular brands

Load more brands