Trocen AWC708S User Manual Download Page 34

Page: 34 / 97

AWC708S Motion Control User Manual

WWW.SZTROCEN.COM

On the main page, press

【

Stop

】

【

Shift

】

at the same time to open

the

Manufacture Params Settings

page. Then move cursor to

【

Axis

Parameters

】

option and press

【

Enter

】

. Then open the

X Axis

Parameters

page and move cursor to

【

Distance Per Pulse

】

, press

【

Enter

】

. Input 200mm into

【

Expected Length

】

and input the distance

between A and B into

【

Actual Length

】

. Then press

【

Enter

】

, the

distance per pulse of X axis will be calculated.

The calculation method of Y axis is the same as X axis.

When Z axis works as lifting shaft or platform lifting shaft, the

calculation method is the same as X axis.

When the pulse distance value of any axis is close to or less than 1, the

pulse distance can’t be adjusted and is always 1. Users need to adjust pulse

of motor driver first, then measure the distance per pulse again. The

recommended pulse distance value is 5 or more.

3.6 Hard Limit and Range

On the main page, press

【

Stop

】

【

Shift

】

at the same time to open the

Manufacture Params Settings

page. Then move cursor to

【

HardLimit

Settings

】

and press

【

Enter

】

, users can enable or disable the hard limit

parameters. AWC708S supports range function, so users don’t need to

install hard limit sensors, just setting

【

Range

】

parameters on the relevant

axis parameters page will be enough.

Set the distance per pulse of X/Y/Z axis according to the content of the

Summary of Contents for AWC708S

































































































Search results

Summary of Contents for AWC708S

Reviews:

Brands by name

Popular brands

Trocen AWC708S, User Manual

Search results

Summary of Contents for AWC708S

Reviews:

Brands by name

Popular brands