background image

                                                               

            -

        - 

                                       

XM340-V1.2 - A 

 

before cleaning it. Only handle the power cord by the plug. Never pull 
out the plug by tugging the power cord. 
 
During initial start-up some smoke or smell may arise. This is a normal 
process and does not necessarily mean that the device is defective, it 
should decrease gradually. 
 
Please don't project the beam onto combustible substances. 

 

Fixtures cannot be installed on combustible substances, keep more than 
50cm distance with wall for smooth air flow, so there should be no 
shelter for fans and ventilation for heat radiation. 
 
If the external flexible cable or cord of this luminaire is damaged, it shall 
be exclusively replaced by the manufacturer or his service agent or a 
similar qualified person in order to avoid a hazard. 

 

Please be aware that damages caused by manual modifications to the 
device are not subject to warranty. Keep away from children and 
non-professionals. 
 

GENERAL GUIDELINES 

This device is a lighting effect for professional use on stages, in 
discotheques, theatres, etc. 

Summary of Contents for WALLY LPAR21




























Reviews: